DDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
f967
rgef1
DDRConf2
DDR3, BW=16 Col=10 Bk=8 CS0 Row=14 CS=1 Die BW=16 Size=256MB
924MHz
DDR bin out

U-Boot SPL board init
U-Boot SPL 2017.09 (Mar 12 2024 - 06:20:28)
unrecognized JEDEC id bytes: ff, ef, aa
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 2
spl: mmc init failed with error: -123
Trying to boot from MTD1
ENVF: Primary 0x00000000 - 0x00040000
ENVF: OK
Trying fit image at 0x400 sector
## Verified-boot: 0
## Checking uboot 0x00200000 (lzma @0x00400000) ... sha256(fcaccef4c7...) + sha256(b502bdde87...) + OK
## Checking fdt 0x0025bfd8 ... sha256(51bba657c3...) + OK
Total: 236.365 ms

Jumping to U-Boot(0x00200000)


U-Boot 2017.09 (Mar 12 2024 - 06:20:28 +0000)

Model: Rockchip RV1106 EVB Board
PreSerial: 2, raw, 0xff4c0000
DRAM:  256 MiB
Sysmem: init
Relocation Offset: 0fd85000
Relocation fdt: 0edfadb0 - 0edfedd8
CR: M/C/I
Using default environment

Bootdev(atags): mtd 1
ENVF: Primary 0x00000000 - 0x00040000
ENVF: OK
PartType: ENV
DM: v2
No misc partition
boot mode: None
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
Model: Luckfox Pico Pro
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 924000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  aclk_peri_root 400000 KHz
  hclK_peri_root 200000 KHz
  pclk_peri_root 100000 KHz
  aclk_bus_root 300000 KHz
  pclk_top_root 100000 KHz
  pclk_pmu_root 100000 KHz
  hclk_pmu_root 200000 KHz
Net:   eth0: ethernet@ffa80000
Hit key to stop autoboot('CTRL+C'):  0 
## Booting FIT Image at 0xe90b180 with size 0x002eec00
Fdt Ramdisk skip relocation
No misc partition
## Loading kernel from FIT Image at 0e90b180 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x0e914980
     Data Size:    3036008 Bytes = 2.9 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x00008000
     Entry Point:  0x00008000
     Hash algo:    sha256
     Hash value:   8ccfc759cfbbdd599b3752be3f5dfe48d0439c4af2a4a85046f16d9fbad2495f
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 0e90b180 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x0e90b980
     Data Size:    36380 Bytes = 35.5 KiB
     Architecture: ARM
     Load Address: 0x00c00000
     Hash algo:    sha256
     Hash value:   45b0918cf26355886aba605124b00c5689161b533bd879770fbc9158c04e2ead
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x00c00000 to 0x00c00000
   Booting using the fdt blob at 0x00c00000
   Loading Kernel Image from 0x0e914980 to 0x00008000 ... OK
   kernel loaded at 0x00008000, end = 0x002ed368
   Using Device Tree in place at 00c00000, end 00c0be1b
Adding bank: 0x00000000 - 0x10000000 (size: 0x10000000)
Total: 539.429 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.10.160 (hxj@luckfox-System-Product-Name) (arm-rockchip830-linux-uclibcgnueabihf-gcc (crosstool-NG 1.24.0) 8.3.0, GNU ld (crosstool-NG 1.24.0) 2.32) #11 Wed May 7 13:54:02 CST 2025
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c53c7d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Luckfox Pico Pro
[    0.000000] Memory policy: Data cache writeback
[    0.000000] cma: Reserved 67584 KiB at 0x0be00000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: user_debug=31 storagemedia=mtd androidboot.storagemedia=mtd androidboot.mode=normal  rootwait earlycon=uart8250,mmio32,0xff4c0000 console=ttyFIQ0 root=ubi0:rootfs snd_soc_core.prealloc_buffer_size_kbytes=16 coherent_pool=0 mtdparts=spi-nand0:256K(env),256K@256K(idblock),512K(uboot),4M(boot),30M(oem),10M(userdata),210M(rootfs) ubi.mtd=6 rootfstype=ubifs rk_dma_heap_cma=66M
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 185536K/262144K available (3793K kernel code, 379K rwdata, 1816K rodata, 196K init, 138K bss, 9024K reserved, 67584K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000018] Switching to timer-based delay loop, resolution 41ns
[    0.000491] Console: colour dummy device 80x30
[    0.000534] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000552] pid_max: default: 4096 minimum: 301
[    0.000718] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000732] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001314] CPU: Testing write buffer coherency: ok
[    0.001907] Setting up static identity map for 0x81c0 - 0x81f8
[    0.002418] devtmpfs: initialized
[    0.009215] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.009386] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.009407] futex hash table entries: 16 (order: -5, 192 bytes, linear)
[    0.009484] pinctrl core: initialized pinctrl subsystem
[    0.010676] NET: Registered protocol family 16
[    0.011078] DMA: failed to allocate 0 KiB pool for atomic coherent allocation
[    0.011626] Registered FIQ tty driver
[    0.011950] thermal_sys: Registered thermal governor 'step_wise'
[    0.011957] thermal_sys: Registered thermal governor 'user_space'
[    0.012183] cpuidle: using governor menu
[    0.025495] rockchip-gpio ff380000.gpio: probed /pinctrl/gpio@ff380000
[    0.026222] rockchip-gpio ff530000.gpio: probed /pinctrl/gpio@ff530000
[    0.026863] rockchip-gpio ff540000.gpio: probed /pinctrl/gpio@ff540000
[    0.027584] rockchip-gpio ff550000.gpio: probed /pinctrl/gpio@ff550000
[    0.028210] rockchip-gpio ff560000.gpio: probed /pinctrl/gpio@ff560000
[    0.028299] rockchip-pinctrl pinctrl: probed pinctrl
[    0.037842] fiq_debugger fiq_debugger.0: IRQ uart_irq not found
[    0.037865] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    0.038127] printk: console [ttyFIQ0] enabled
[    0.038301] Registered fiq debugger ttyFIQ0
[    0.039398] reg-fixed-voltage vdd-arm: Fixed regulator specified with variable voltages
[    0.039430] reg-fixed-voltage: probe of vdd-arm failed with error -22
[    0.040093] SCSI subsystem initialized
[    0.040296] usbcore: registered new interface driver usbfs
[    0.040353] usbcore: registered new interface driver hub
[    0.040403] usbcore: registered new device driver usb
[    0.040625] mc: Linux media interface: v0.10
[    0.040668] videodev: Linux video capture interface: v2.00
[    0.041753] Advanced Linux Sound Architecture Driver Initialized.
[    0.042455] rockchip-cpuinfo cpuinfo: SoC            : 11061000
[    0.042478] rockchip-cpuinfo cpuinfo: Serial         : 970e8656690ea1c6
[    0.042841] rockchip,rknpor-powergood ff000000.syscon:rknpor-powergood: probe success!
[    0.043591] clocksource: Switched to clocksource arch_sys_counter
[    0.049574] NET: Registered protocol family 2
[    0.049804] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.050333] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.050373] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.050398] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.050423] TCP: Hash tables configured (established 2048 bind 2048)
[    0.050509] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.050530] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.050653] NET: Registered protocol family 1
[    0.051307] RPC: Registered named UNIX socket transport module.
[    0.051327] RPC: Registered udp transport module.
[    0.051333] RPC: Registered tcp transport module.
[    0.051340] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.052280] rockchip-thermal ff3c8000.tsadc: tsadc is probed successfully!
[    0.053277] Initialise system trusted keyrings
[    0.053507] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    0.057133] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.057893] NFS: Registering the id_resolver key type
[    0.057957] Key type id_resolver registered
[    0.057966] Key type id_legacy registered
[    0.058009] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.058475] Key type asymmetric registered
[    0.058498] Asymmetric key parser 'x509' registered
[    0.058527] io scheduler mq-deadline registered
[    0.058872] rockchip-usb2phy ff3e0000.usb2-phy: IRQ index 0 not found
[    0.063666] dma-pl330 ff420000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.063691] dma-pl330 ff420000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    0.064435] rockchip-pvtm ff240000.pvtm: pvtm@0 probed
[    0.064588] rockchip-pvtm ff390000.pvtm: pvtm@0 probed
[    0.064885] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    0.065401] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    0.071042] random: crng init done
[    0.079077] brd: module loaded
[    0.084362] loop: module loaded
[    0.086402] spi-nand spi2.0: Winbond SPI NAND was found.
[    0.086436] spi-nand spi2.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    0.087462] 7 cmdlinepart partitions found on MTD device spi-nand0
[    0.087479] Creating 7 MTD partitions on "spi-nand0":
[    0.087492] 0x000000000000-0x000000040000 : "env"
[    0.089181] 0x000000040000-0x000000080000 : "idblock"
[    0.090772] 0x000000080000-0x000000100000 : "uboot"
[    0.092346] 0x000000100000-0x000000500000 : "boot"
[    0.094061] 0x000000500000-0x000002300000 : "oem"
[    0.095781] 0x000002300000-0x000002d00000 : "userdata"
[    0.097409] 0x000002d00000-0x00000ff00000 : "rootfs"
[    0.101103] rk_gmac-dwmac ffa80000.ethernet: IRQ eth_lpi not found
[    0.101281] rk_gmac-dwmac ffa80000.ethernet: PTP uses main clock
[    0.101329] rk_gmac-dwmac ffa80000.ethernet: no regulator found
Seeding 256 bits and crediting
[    0.101343] rk_gmac-dwmac ffa80000.ethernet: clock input or output? (input).
Saving 256 bits of creditable seed for next boot
[    0.101355] rk_gmac-dwmac ffa80000.ethernet: Can not read property: tx_delay.
Starting syslogd: OK
[    0.101363] rk_gmac-dwmac ffa80000.ethernet: set tx_delay to 0xffffffff
[    0.101373] rk_gmac-dwmac ffa80000.ethernet: Can not read property: rx_delay.
Starting klogd: OK
[    0.101381] rk_gmac-dwmac ffa80000.ethernet: set rx_delay to 0xffffffff
[    0.101455] rk_gmac-dwmac ffa80000.ethernet: integrated PHY? (yes).
[    0.101474] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_rx
Running sysctl: [    0.101487] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_tx
[    0.101517] rk_gmac-dwmac ffa80000.ethernet: cannot get clock clk_mac_speed
[    0.101527] rk_gmac-dwmac ffa80000.ethernet: clock input from PHY
[    0.101772] rk_gmac-dwmac ffa80000.ethernet: init for RMII
[    0.101965] rk_gmac-dwmac ffa80000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    0.101987] rk_gmac-dwmac ffa80000.ethernet:         DWMAC4/5
[    0.102001] rk_gmac-dwmac ffa80000.ethernet: DMA HW capability register supported
[    0.102010] rk_gmac-dwmac ffa80000.ethernet: RX Checksum Offload Engine supported
[    0.102018] rk_gmac-dwmac ffa80000.ethernet: TX Checksum insertion supported
OK
[    0.102026] rk_gmac-dwmac ffa80000.ethernet: Wake-Up On Lan supported
Populating /dev using udev: [    0.102033] rk_gmac-dwmac ffa80000.ethernet: TSO supported
[    0.102042] rk_gmac-dwmac ffa80000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.102050] rk_gmac-dwmac ffa80000.ethernet: TSO feature enabled
[    0.102061] rk_gmac-dwmac ffa80000.ethernet: Using 40 bits DMA width
[    0.109210] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.109542] usbcore: registered new interface driver usb-storage
[    0.109694] gadgetfs: USB Gadget filesystem, version 24 Aug 2004
[    0.109737] Mass Storage Function, version: 2009/09/11
[    0.109751] LUN: removable file: (no medium)
[    0.109778] no file given for LUN0
[    0.109809] udc ffb00000.usb: failed to start g_mass_storage: -22
[    0.111209] rockchip-rtc ff1c0000.rtc: registered as rtc0
[    0.111282] rockchip-rtc ff1c0000.rtc: setting system clock to 2021-01-01T12:16:39 UTC (1609503399)
[    0.111503] i2c /dev entries driver
[    0.113823] usbcore: registered new interface driver uvcvideo
[    0.113846] USB Video Class driver (1.1.1)
[    0.114611] cpu cpu0: leakage=18
[    0.115191] Synopsys Designware Multimedia Card Interface Driver
[    0.116027] dtbocfg: 0.1.0
[    0.116069] dtbocfg: OK
[    0.117290] dwmmc_rockchip ffaa0000.mmc: No normal pinctrl state
[    0.117317] dwmmc_rockchip ffaa0000.mmc: No idle pinctrl state
[    0.117439] dwmmc_rockchip ffaa0000.mmc: IDMAC supports 32-bit address mode.
[    0.117477] dwmmc_rockchip ffaa0000.mmc: Using internal DMA controller.
[    0.117494] dwmmc_rockchip ffaa0000.mmc: Version ID is 270a
[    0.117535] dwmmc_rockchip ffaa0000.mmc: DW MMC controller at irq 51,32 bit host data width,256 deep fifo
[    0.119027] rv1106-acodec ff480000.acodec: current soc_id: rv1106
[    0.119120] rv1106-acodec ff480000.acodec: Use pa_ctl_gpio and pa_ctl_delay_ms: 0
[    0.120670] NET: Registered protocol family 17
[    0.120774] Key type dns_resolver registered
[    0.121622] Loading compiled-in X.509 certificates
[    0.136878] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.148516] input: adc-keys as /devices/platform/adc-keys/input/input0
[    0.225325] ubi0: attaching mtd6
[    0.596780] ubi0: scanning is finished
[    0.602298] ubi0: attached mtd6 (name "rootfs", size 210 MiB)
[    0.602323] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    0.602333] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    0.602341] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    0.602349] ubi0: good PEBs: 1680, bad PEBs: 0, corrupted PEBs: 0
[    0.602358] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    0.602368] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2099566698
[    0.602379] ubi0: available PEBs: 0, total reserved PEBs: 1680, PEBs reserved for bad PEB handling: 40
[    0.603521] ALSA device list:
[    0.603540]   #0: rv-acodec
[    0.604106] ubi0: background thread "ubi_bgt0d" started, PID 56
[    0.604324] UBIFS (ubi0:0): Mounting in unauthenticated mode
[    0.636254] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[    0.636284] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    0.636299] UBIFS (ubi0:0): FS size: 206336000 bytes (196 MiB, 1625 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    0.636309] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[    0.636320] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 27FC8EAF-3F0C-42D3-9FE6-AFD6B5FFF47E, small LPT model
[    0.637427] VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
[    0.638135] devtmpfs: mounted
[    0.638325] Freeing unused kernel memory: 196K
[    0.638334] Kernel memory protection not selected by kernel config.
[    0.638362] Run /sbin/init as init process
[    0.645007] process '/bin/busybox' started with executable stack
[    0.710600] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 59
[    0.946852] udevd[91]: starting version 3.2.7
[    0.962196] udevd[91]: specified group 'input' unknown
[    0.963162] udevd[91]: specified group 'kvm' unknown
[    0.983159] udevd[92]: starting eudev-3.2.7
[    1.334414] udevd[103]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd0ro': No such file or directory
[    1.342009] udevd[104]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd1ro': No such file or directory
[    1.351075] udevd[105]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd2ro': No such file or directory
[    1.358717] udevd[106]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd3ro': No such file or directory
[    1.364643] udevd[107]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd4ro': No such file or directory
[    1.371713] udevd[108]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd5ro': No such file or directory
[    1.379962] udevd[109]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd6ro': No such file or directory
done
/etc/init.d/S20linkmount info: mount point path [IGNORE] not found, skip...
***********/dev/ubi4_0 not exist***********
***********/dev/ubi4 not exist***********
[    1.769985] ubi4: attaching mtd4
[    1.822756] ubi4: scanning is finished
[    1.830266] ubi4: attached mtd4 (name "oem", size 30 MiB)
[    1.830293] ubi4: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI device number 4, total 240 LEBs (30474240 bytes, 29.1 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[    1.830303] ubi4: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
try to make volume: /dev/ubi4_0 ...
[    1.830313] ubi4: VID header offset: 2048 (aligned 2048), data offset: 4096
ubimkvol: error!: bad volume size: "0"
[    1.830322] ubi4: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[    1.830330] ubi4: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.830341] ubi4: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 609975783
[    1.830351] ubi4: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 40
[    1.831498] ubi4: background thread "ubi_bgt4d" started, PID 129
[    1.858791] UBIFS (ubi4:0): Mounting in unauthenticated mode
[    1.858995] UBIFS (ubi4:0): background thread "ubifs_bgt4_0" started, PID 134
[    1.888485] UBIFS (ubi4:0): UBIFS: mounted UBI device 4, volume 0, name "oem"
***********/dev/ubi5_0 not exist***********
[    1.888510] UBIFS (ubi4:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
***********/dev/ubi5 not exist***********
[    1.888523] UBIFS (ubi4:0): FS size: 23617536 bytes (22 MiB, 186 LEBs), journal size 4190208 bytes (3 MiB, 33 LEBs)
UBI device number 5, total 80 LEBs (10158080 bytes, 9.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[    1.888533] UBIFS (ubi4:0): reserved for root: 0 bytes (0 KiB)
try to make volume: /dev/ubi5_0 ...
[    1.888546] UBIFS (ubi4:0): media format: w4/r0 (latest is w5/r0), UUID E127883C-B994-40B1-83D7-7DE7EF113C9D, small LPT model
ubimkvol: error!: bad volume size: "0"
[    1.928075] ubi5: attaching mtd5
[    1.946102] ubi5: scanning is finished
[    1.953148] ubi5: attached mtd5 (name "userdata", size 10 MiB)
[    1.953171] ubi5: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.953182] ubi5: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.953191] ubi5: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.953199] ubi5: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
[    1.953209] ubi5: user volume: 1, internal volumes: 1, max. volumes count: 128
Initializing random number generator... [    1.953219] ubi5: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1975413781
done.
[    1.953230] ubi5: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 40
[    1.956101] ubi5: background thread "ubi_bgt5d" started, PID 143
[    1.977119] UBIFS (ubi5:0): Mounting in unauthenticated mode
[    1.977330] UBIFS (ubi5:0): background thread "ubifs_bgt5_0" started, PID 148
Starting iptables: [    2.016177] UBIFS (ubi5:0): UBIFS: mounted UBI device 5, volume 0, name "userdata"
/dev/ubi5_0 on /userdata type ubifs (rw,relatime,assert=read-only,ubi=5,vol=0)
[    2.016205] UBIFS (ubi5:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.016217] UBIFS (ubi5:0): FS size: 3301376 bytes (3 MiB, 26 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs)
[    2.016227] UBIFS (ubi5:0): reserved for root: 0 bytes (0 KiB)
[    2.016240] UBIFS (ubi5:0): media format: w4/r0 (latest is w5/r0), UUID 8C00C30A-F29F-4DD1-9F4B-FA6BD1C35163, small LPT model
OK
Starting network: OK
Starting ntpd: /
ln: /usr/www/userdata: No such file or directory
ln: /usr/www/usb0: No such file or directory
[    2.597502] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
ln: /usr/www/sdcard: No such file or directory
eth HWaddr cfg ok
md5sum: can't open '/tmp/rkipc-factory-config.ini': No such file or directory
Error: not found rkipc.ini !!!
/oem/usr/bin/RkLunch.sh: exit: line 110: Illegal number: -1
[    2.817519] rk_gmac-dwmac ffa80000.ethernet eth0: PHY [stmmac-0:02] driver [RK630 PHY] (irq=POLL)
[    2.817871] dwmac4: Master AXI performs any burst length
[    2.817898] rk_gmac-dwmac ffa80000.ethernet eth0: No Safety Features support found
[    2.817918] rk_gmac-dwmac ffa80000.ethernet eth0: PTP not supported by HW
udhcpc: started, v1.36.1
[    2.818233] rk_gmac-dwmac ffa80000.ethernet eth0: configuring for phy/rmii link mode
OK
[    2.837517] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
Starting fcn: udhcpc: broadcasting discover
[    3.631867] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
udhcpc: broadcasting discover
OK
Starting ksa: udhcpc: broadcasting discover
OK
Starting sshd: OK
Starting telnetd: [   13.228823] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
OK
[   13.257848] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
/etc/init.d/S50usbdevice: line 144: can't open : no such file
Debug: configfs_init
[   13.350141] file system registered
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
[   13.375359] using random self ethernet address
[   13.375384] using random host ethernet address
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/acm.gs6': No such file or directory
[   13.395205] Mass Storage Function, version: 2009/09/11
[   13.395235] LUN: removable file: (no medium)
[   13.478662] read descriptors
[   13.478831] read strings
[   14.475349] usb0: HOST MAC 9a:25:6f:4d:7e:72
[   14.475372] usb0: MAC 0e:93:0e:d8:28:12
[   14.589535] dwc3 ffb00000.usb: device reset
[   14.651333] android_work: sent uevent USB_STATE=CONNECTED
[   14.657968] android_work: sent uevent USB_STATE=CONFIGURED
current_ip = 
TARGET_IP = 172.32.0.93
luckfox : set usb0 ip
[   15.532697] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '

[   15.555655] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
luckfox : set usb0 ip

luckfox : set usb0 ip

[   16.633383] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   16.641906] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
luckfox : set usb0 ip

luckfox : set usb0 ip

luckfox : set usb0 ip

luckfox : set usb0 ip

luckfox : set usb0 ip

luckfox : set usb0 ip

luckfox : set usb0 ip

usb0 config error
Starting SMB services: [   22.549180] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   22.557780] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   22.605612] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   22.614242] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
OK
Starting NMB services: [   22.885264] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   22.905687] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   24.064078] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   24.074214] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
OK
[   24.115098] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
/root/main.py and /root/boot.py not exist ,pass...
OK
[   24.131935] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   24.160129] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '
[   24.168807] ipv6: version magic '5.10.110 mod_unload ARMv7 thumb2 p2v8 ' should be '5.10.160 mod_unload ARMv7 thumb2 p2v8 '

Welcome to luckfox pico
luckfox pico login: udhcpc: broadcasting discover