怎么解决？开机日志如下
S5P1
f967
rgef1
DDRConf2
DDR3, BW=16 Col=10 Bk=8 CS0 Row=14 CS=1 Die BW=16 Size=256MB
924MHz
DDR bin out
U-Boot SPL board init
U-Boot SPL 2017.09 (May 07 2024 - 10:25:51)
unrecognized JEDEC id bytes: ff, ef, aa
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 2
spl: mmc init failed with error: -123
Trying to boot from MTD1
ENVF: Primary 0x00000000 - 0x00040000
ENVF: OK
Trying fit image at 0x400 sector
## Verified-boot: 0
## Checking uboot 0x00200000 (lzma @0x00400000) ... sha256(efc97bd844...) + sha256(355a0ac7d8...) + OK
## Checking fdt 0x0025bfd8 ... sha256(51bba657c3...) + OK
Total: 235.784 ms
Jumping to U-Boot(0x00200000)
U-Boot 2017.09 (May 07 2024 - 10:25:51 +0800)
Model: Rockchip RV1106 EVB Board
PreSerial: 2, raw, 0xff4c0000
DRAM: 256 MiB
Sysmem: init
Relocation Offset: 0fd85000
Relocation fdt: 0edfadb0 - 0edfedd8
CR: M/C/I
Using default environment
Bootdev(atags): mtd 1
ENVF: Primary 0x00000000 - 0x00040000
ENVF: OK
PartType: ENV
DM: v2
No misc partition
boot mode: None
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
Model: Luckfox Pico Max
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 924000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
aclk_peri_root 400000 KHz
hclK_peri_root 200000 KHz
pclk_peri_root 100000 KHz
aclk_bus_root 300000 KHz
pclk_top_root 100000 KHz
pclk_pmu_root 100000 KHz
hclk_pmu_root 200000 KHz
Net: eth0: ethernet@ffa80000
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image at 0xe940580 with size 0x002b9800
Fdt Ramdisk skip relocation
No misc partition
## Loading kernel from FIT Image at 0e940580 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0x0e949780
Data Size: 2819392 Bytes = 2.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00008000
Entry Point: 0x00008000
Hash algo: sha256
Hash value: 8de0ec6bf63e4324ba1754d13bf80fd309dddf7a01f631d7b4356d1edb730342
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 0e940580 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x0e940d80
Data Size: 35117 Bytes = 34.3 KiB
Architecture: ARM
Load Address: 0x00c00000
Hash algo: sha256
Hash value: 0f905bc6792ac7120a19bd62ef3d2e43e0278df566d44e54d2c11d22c7292fa3
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x00c00000 to 0x00c00000
Booting using the fdt blob at 0x00c00000
Loading Kernel Image from 0x0e949780 to 0x00008000 ... OK
kernel loaded at 0x00008000, end = 0x002b8540
Using Device Tree in place at 00c00000, end 00c0b92c
Adding bank: 0x00000000 - 0x10000000 (size: 0x10000000)
Total: 521.9 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.110 (ubantu22@ubantu22) (arm-rockchip830-linux-uclibcgnueabihf-gcc (crosstool-NG 1.24.0) 8.3.0, GNU ld (crosstool-NG 1.24.0) 2.32) #1 Fri May 24 10:46:24 CST 2024
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Luckfox Pico Max
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 1024 KiB at 0x0ff00000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: user_debug=31 storagemedia=mtd androidboot.storagemedia=mtd androidboot.mode=normal rootwait earlycon=uart8250,mmio32,0xff4c0000 console=ttyFIQ0 snd_soc_core.prealloc_buffer_size_kbytes=16 coherent_pool=0 ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rk_dma_heap_cma=1M mtdparts=spi-nand0:256K(env),256K@256K(idblock),512K(uboot),4M(boot),30M(oem),10M(userdata),210M(rootfs)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 252632K/262144K available (3543K kernel code, 292K rwdata, 1680K rodata, 164K init, 132K bss, 8488K reserved, 1024K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x1fb/0x360 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000017] Switching to timer-based delay loop, resolution 41ns
[ 0.000375] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.000393] pid_max: default: 4096 minimum: 301
[ 0.000550] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000564] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001135] CPU: Testing write buffer coherency: ok
[ 0.001586] Setting up static identity map for 0x81c0 - 0x81f8
[ 0.002022] devtmpfs: initialized
[ 0.008515] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.008678] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.008703] futex hash table entries: 16 (order: -5, 192 bytes, linear)
[ 0.008782] pinctrl core: initialized pinctrl subsystem
[ 0.009503] NET: Registered protocol family 16
[ 0.009822] DMA: failed to allocate 0 KiB pool for atomic coherent allocation
[ 0.010534] thermal_sys: Registered thermal governor 'step_wise'
[ 0.010541] thermal_sys: Registered thermal governor 'user_space'
[ 0.010780] cpuidle: using governor menu
[ 0.010807] Registered FIQ tty driver
[ 0.024946] rockchip-gpio ff380000.gpio: probed /pinctrl/gpio@ff380000
[ 0.025733] rockchip-gpio ff530000.gpio: probed /pinctrl/gpio@ff530000
[ 0.026352] rockchip-gpio ff540000.gpio: probed /pinctrl/gpio@ff540000
[ 0.027096] rockchip-gpio ff550000.gpio: probed /pinctrl/gpio@ff550000
[ 0.027691] rockchip-gpio ff560000.gpio: probed /pinctrl/gpio@ff560000
[ 0.027773] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.035574] fiq_debugger fiq_debugger.0: IRQ uart_irq not found
[ 0.035597] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 0.035852] printk: console [ttyFIQ0] enabled
[ 0.036017] Registered fiq debugger ttyFIQ0
[ 0.038341] usbcore: registered new interface driver usbfs
[ 0.038403] usbcore: registered new interface driver hub
[ 0.038455] usbcore: registered new device driver usb
[ 0.038676] mc: Linux media interface: v0.10
[ 0.038718] videodev: Linux video capture interface: v2.00
[ 0.039727] Advanced Linux Sound Architecture Driver Initialized.
[ 0.040504] rockchip-cpuinfo cpuinfo: SoC : 11061000
[ 0.040530] rockchip-cpuinfo cpuinfo: Serial : fc0ce68193019ca5
[ 0.040921] rockchip,rknpor-powergood ff000000.syscon:rknpor-powergood: probe success!
[ 0.041543] clocksource: Switched to clocksource arch_sys_counter
[ 0.042699] NET: Registered protocol family 2
[ 0.042855] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.043401] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.043462] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.043528] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.043553] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.043679] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.043714] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.043842] NET: Registered protocol family 1
[ 0.044308] RPC: Registered named UNIX socket transport module.
[ 0.044325] RPC: Registered udp transport module.
[ 0.044334] RPC: Registered tcp transport module.
[ 0.044341] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.045319] Initialise system trusted keyrings
[ 0.045524] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.049427] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.050136] NFS: Registering the id_resolver key type
[ 0.050182] Key type id_resolver registered
[ 0.050199] Key type id_legacy registered
[ 0.050246] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.050699] Key type asymmetric registered
[ 0.050726] Asymmetric key parser 'x509' registered
[ 0.050757] io scheduler mq-deadline registered
[ 0.051018] rockchip-usb2phy ff3e0000.usb2-phy: IRQ index 0 not found
[ 0.057052] dma-pl330 ff420000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 0.057078] dma-pl330 ff420000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.057870] rockchip-pvtm ff240000.pvtm: pvtm@0 probed
[ 0.058067] rockchip-pvtm ff390000.pvtm: pvtm@0 probed
[ 0.058684] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 0.059367] ff4d0000.serial: ttyS3 at MMIO 0xff4d0000 (irq = 38, base_baud = 1500000) is a 16550A
[ 0.060181] ff4e0000.serial: ttyS4 at MMIO 0xff4e0000 (irq = 39, base_baud = 1500000) is a 16550A
[ 0.065606] random: fast init done
[ 0.065742] random: crng init done
[ 0.075530] brd: module loaded
[ 0.081238] loop: module loaded
[ 0.082552] rockchip-spi ff500000.spi: no high_speed pinctrl state
[ 0.085002] spi-nand spi2.0: Winbond SPI NAND was found.
[ 0.085031] spi-nand spi2.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 0.086111] 7 cmdlinepart partitions found on MTD device spi-nand0
[ 0.086126] Creating 7 MTD partitions on "spi-nand0":
[ 0.086143] 0x000000000000-0x000000040000 : "env"
[ 0.087923] 0x000000040000-0x000000080000 : "idblock"
[ 0.089658] 0x000000080000-0x000000100000 : "uboot"
[ 0.091347] 0x000000100000-0x000000500000 : "boot"
[ 0.093114] 0x000000500000-0x000002300000 : "oem"
[ 0.094977] 0x000002300000-0x000002d00000 : "userdata"
[ 0.096700] 0x000002d00000-0x00000ff00000 : "rootfs"
[ 0.100545] rk_gmac-dwmac ffa80000.ethernet: IRQ eth_lpi not found
[ 0.100704] rk_gmac-dwmac ffa80000.ethernet: PTP uses main clock
[ 0.100745] rk_gmac-dwmac ffa80000.ethernet: no regulator found
[ 0.100757] rk_gmac-dwmac ffa80000.ethernet: clock input or output? (input).
[ 0.100768] rk_gmac-dwmac ffa80000.ethernet: Can not read property: tx_delay.
[ 0.100777] rk_gmac-dwmac ffa80000.ethernet: set tx_delay to 0xffffffff
[ 0.100787] rk_gmac-dwmac ffa80000.ethernet: Can not read property: rx_delay.
[ 0.100795] rk_gmac-dwmac ffa80000.ethernet: set rx_delay to 0xffffffff
[ 0.100867] rk_gmac-dwmac ffa80000.ethernet: integrated PHY? (yes).
[ 0.100883] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_rx
[ 0.100895] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_tx
[ 0.100937] rk_gmac-dwmac ffa80000.ethernet: cannot get clock clk_mac_speed
[ 0.100946] rk_gmac-dwmac ffa80000.ethernet: clock input from PHY
[ 0.101195] rk_gmac-dwmac ffa80000.ethernet: init for RMII
[ 0.101387] rk_gmac-dwmac ffa80000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.101408] rk_gmac-dwmac ffa80000.ethernet: DWMAC4/5
[ 0.101420] rk_gmac-dwmac ffa80000.ethernet: DMA HW capability register supported
[ 0.101429] rk_gmac-dwmac ffa80000.ethernet: RX Checksum Offload Engine supported
[ 0.101447] rk_gmac-dwmac ffa80000.ethernet: TX Checksum insertion supported
[ 0.101457] rk_gmac-dwmac ffa80000.ethernet: Wake-Up On Lan supported
[ 0.101464] rk_gmac-dwmac ffa80000.ethernet: TSO supported
[ 0.101472] rk_gmac-dwmac ffa80000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.101480] rk_gmac-dwmac ffa80000.ethernet: TSO feature enabled
[ 0.101490] rk_gmac-dwmac ffa80000.ethernet: Using 40 bits DMA width
[ 0.110713] rockchip-rtc ff1c0000.rtc: rockchip_rtc_compensation:timeout waiting for RTC TEST STATUS : -110
[ 0.111095] rtc rtc0: invalid alarm value: 2000-10-04T28:00:10
[ 0.111485] rockchip-rtc ff1c0000.rtc: registered as rtc0
[ 0.111Seeding 2048 bits and crediting
Saving 2048 bits of creditable seed for next boot
819] i2c /dev entries driver
[ 0.113688] i2c i2c-4: 1 i2c clients have been registered at 0x30
[ 0.114075] i2c Starting syslogd: i2c-4: 2 i2c clients have been registered at 0x30
[ 0.116252] rockchip-thermal ff3c8000.tsadc: tsadcOK
is probed successfully!
[ 0.116829] cpu cpu0: Failed to get cpu_leakage
[ 0.118051] cpu cpu0: avs=0
[ 0.118624] cpu cpu0: rockchip_pvtpll_set_volt:Starting klogd: failed to set vdd voltage (925000 1050000 uV): -22
[ 0.118804] cpu cpOK
u0: failed to register system monitor
[ 0.119266] Synopsys Designware Multimedia Card Interface Driver
[ 0.120193] dwmmc_rockchip ffaa0000.mmc: IDMAC supports 32-bit address mode.
[ 0.120241] dwmmc_rockchip ffaa0000.mmc: Using internal DMA controller.
[ 0.120258] dwmmc_rockchip ffaa0Running sysctl: 000.mmc: Version ID is 270a
[ 0.120301] dwmmc_rockchip ffaa0000.mmc: DW MMC controller at irq 54,32 bit host data width,256 deep fifo
[ 0.123623] rv1106-acodec ff480000.acodec: current soc_id: rv1106
[ 0.123727] rv1106-acodec ff480000.acodec: Use pa_ctl_gpio and pa_ctl_delay_ms: 0
[ 0.125618] NET: Registered protocol family 17
[ 0.125731] Key type dns_resolver registered
[ 0.126566] Loading compiled-in X.509 certificates
[ 0.127145]
[ 0.127166] ********************************************************************
[ 0.127176] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.127184] ** **
[ 0.127190] ** WRITEABLE clk DebugFS SUPPORT HAS BEEOK
N ENABLED IN THIS KERNEL **
[ 0.127196] ** Populating /dev using udev: **
[ 0.127202] ** This means that this kernel is built to expose clk operations **
[ 0.127209] ** such as parent or rate setting, enabling, disabling, etc. **
[ 0.127215] ** to userspace, which may compromise security on your system. **
[ 0.127220] ** **
[ 0.127227] ** If you see this message and you are not debugging the **
[ 0.127233] ** kernel, report this immediately to your vendor! **
[ 0.127238] ** **
[ 0.127244] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
[ 0.127250] ********************************************************************
[ 0.131735] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 0.145913] input: adc-keys as /devices/platform/adc-keys/input/input0
[ 0.213189] ubi0: attaching mtd6
[ 0.608266] ubi0: scanning is finished
[ 0.614003] ubi0: attached mtd6 (name "rootfs", size 210 MiB)
[ 0.614026] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 0.614035] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 0.614044] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 0.614053] ubi0: good PEBs: 1680, bad PEBs: 0, corrupted PEBs: 0
[ 0.614062] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 0.614072] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 31431980
[ 0.614081] ubi0: available PEBs: 0, total reserved PEBs: 1680, PEBs reserved for bad PEB handling: 40
[ 0.615158] ALSA device list:
[ 0.615189] #0: rv-acodec
[ 0.615756] ubi0: background thread "ubi_bgt0d" started, PID 57
[ 0.616004] UBIFS (ubi0:0): Mounting in unauthenticated mode
[ 0.631732] UBIFS (ubi0:0): recovery needed
[ 0.663970] UBIFS (ubi0:0): recovery deferred
[ 0.664091] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[ 0.664110] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 0.664123] UBIFS (ubi0:0): FS size: 206336000 bytes (196 MiB, 1625 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 0.664133] UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
[ 0.664144] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID BBC60995-13A2-4EE8-9A18-B9B68C6F9C95, small LPT model
[ 0.665125] VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
[ 0.665791] devtmpfs: mounted
[ 0.665969] Freeing unused kernel memory: 164K
[ 0.665982] Kernel memory protection not selected by kernel config.
[ 0.666015] Run /sbin/init as init process
[ 0.672117] process '/bin/busybox' started with executable stack
[ 0.738889] UBIFS (ubi0:0): completing deferred recovery
[ 0.817899] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 60
[ 0.827735] UBIFS (ubi0:0): deferred recovery completed
[ 1.108860] udevd[90]: starting version 3.2.7
[ 1.124477] udevd[90]: specified group 'input' unknown
[ 1.126015] udevd[90]: specified group 'kvm' unknown
[ 1.148381] udevd[91]: starting eudev-3.2.7
[ 1.565378] udevd[101]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd0ro': No such file or directory
[ 1.568817] udevd[102]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd1ro': No such file or directory
[ 1.569225] udevd[103]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd2ro': No such file or directory
[ 1.593976] udevd[108]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd3ro': No such file or directory
[ 1.602063] udevd[109]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd4ro': No such file or directory
[ 1.616785] udevd[110]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd5ro': No such file or directory
[ 1.621280] udevd[111]: failed to execute '/lib/udev/mtd_probe' 'mtd_probe /dev/mtd6ro': No such file or directory
done
/etc/init.d/S20linkmount info: mount point path [IGNORE] not found, skip...
***********/dev/ubi4_0 not exist***********
***********/dev/ubi4 not exist***********
[ 1.930224] ubi4: attaching mtd4
[ 1.987052] ubi4: scanning is finished
[ 1.994536] ubi4: attached mtd4 (name "oem", size 30 MiB)
[ 1.994562] ubi4: PEB size:UBI device numbe 131r 4, total 240 LEBs (30474240 bytes, 29.1 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.994570] ubi4: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.994580] ubi4: VID header offtry to make volume: /dev/ubi4_0 ...
set: 2048 (aligned 2048), data offset: 4096
[ 1.994589] ubi4: good PEBs: 240, baubimkvol: error!: bad volume size: "0"
d PEBs: 0, corrupted PEBs: 0
[ 1.994598] ubi4: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.994609] ubi4: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1856996626
[ 1.994619] ubi4: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 40
[ 1.996725] ubi4: background thread "ubi_bgt4d" started, PID 131
[ 2.043822] UBIFS (ubi4:0): Mounting in unauthenticated mode
[ 2.044045] UBIFS (ubi4:0): background thread "ubifs_bgt4_0" started, PID 136
[ 2.060239] UBIFS (ubi4:0): recovery needed
[ 2.125653] UBIFS (ubi4:0): recovery completed
[ 2.128645] UBIFS (ubi4:0): UBIFS: mounted UBI device 4, volume 0, name "oem"
[ 2.128667] UBIFS (ubi4:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.128680] UBIFS (ubi4:0): FS size: 23617536 bytes (22 MiB, 186 LEBs), journal size 4190208 bytes (3 MiB, 33 LEBs)
[ 2.128689] UBIFS (ubi4:0): reserved for root: 0 bytes (0 KiB)
[ 2.128701] UBIFS (ubi4:0): media format: w4/r0 (latest is w5/r0), UUID 262AFF5D-F8C4-4EF7-A1EC-346C7F5AE7C***********/dev/ubi5_0 not exist***********
***********/dev/ubi5 not exist***********
A, small LPT model
[ 2.179084] ubi5: attaching mtd5
[ 2.198702] ubi5: scanning is finished
[ 2.206035] ubi5: attached mtd5 (name "userdata", size 10 MiB)
[ 2.2060UBI device numbe60] ubi5r 5, total 80 LEBs (10158080 bytes: P, 9.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
EB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.206069] ubi5: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.206try to make volume: /dev/ubi5_0 ...
078] ubi5: VID header offset: 2048 (ubimkvol: error!: bad volume size: "0"
aligned 2048), data offset: 4096
[ 2.206086] ubi5: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
[ 2.206095] ubi5: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 2.206106] ubi5: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1592712652
[ 2.206116] ubi5: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 40
[ 2.209408] ubi5: background thread "ubi_bgt5d" started, PID 145
[ 2.249224] UBIFS (ubi5:0): Mounting in unauthenticated mode
[ 2.249460] UBIFS (ubi5:0): background thread "ubifs_bgt5_0" started, PID 150
[ 2.265740] UBIFS (ubi5:0): recovery needed
[ 2.309474] UBIFS (ubi5:0): recovery completed
[ 2.312101] UBIFS (ubi5:0): UBIFS: mounted UBI device 5, volume 0, name "userdata"
[ 2.312122] UBIFS (ubi5:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytesInitializing random number generator...
[ 2.312136] UBIFS (ubi5:0): FS size: 3301376 bytes (3 MiB, 26 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs)
[ 2.312145] UBIFS (ubi5:0): reserved for root: 0 bytes (0 KiB)
[ 2.312158] UBIFS (ubi5:0): media formdone.
at: w4/r0 (latest is w5/r0), UUID 81B7A3E1-2605-4396-B4BC-D34094FCF60D, small LPT model
/dev/ubi5_0 on /userdata type ubifs (rw,relatime,assert=read-only,ubi=5,vol=0)
Starting network: [ 2.476213] rk_dvbm ffa70000.rkdvbm: probe start
[ 2.476314] rk_dvbm ffa70000.rkdvbm: dvbm ctx 093510f0
[ 2.478265] rk_dvbm ffa70000.rkdvbm: probe success
[ 2.520705] rkcifhw ffa10000.rkcif: no iommu attached, using non-iommu buffers
[ 2.520738] rkcifhw ffa10000.rkcif: No reserved memory region assign to CIF
[ 2.522905] rkcif rkcif-mipi-lvds: rkcif driver version: v00.01.0a
[ 2.523026] rkcif rkcif-mipi-lvds: attach to cif hw node
[ 2.523040] rkcif rkcif-mipi-lvds: failed to get dphy hw node
[ 2.523051] rkcif rkcif-mipi-lvds: rkcif wait line 0
[ 2.523064] : terminal subdev does not exist
[ 2.5OK
23089] : terminal subdev does not exist
[ 2.523096] : terminal subdev does not exist
[ 2.523104] : terminal subdev does not exist
[ 2.523114] : get_remote_sensor: video pad[0] is null
[ 2.523123] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.523133] : get_remote_sensor: video pad[0] is null
[ 2.523141] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.523149] : get_remote_sensor: video pad[0] is null
[ 2.523156] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.523164] : get_remote_sensor: video pad[0] is null
[ 2.523170] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.535346] rkcif rkcif-mipi-lvds: No memory-region-thunderboot specified
[ 2.539727] rkcif rkcif-mipi-lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 2.539759] rockchip-mipi-csi2: Async registered subdev
[ 2.539770] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds!
[ 2.585723] rkisp_hw ffa00000.rkisp: is_thunderboot: 0
[ 2.585751] rkisp_hw ffa00000.rkisp: max input:0x0@0fps
[ 2.585763] rkisp_hw ffa00000.rkisp: Missing rockchip,grf property
[ 2.586272] rkisp_hw ffa00000.rkisp: get sram size:258048
[ 2.586292] rkisp_hw ffa00000.rkisp: no iommu attached, using non-iommu buffers
[ 2.586303] rkisp_hw ffa00000.rkisp: No reserved memory region. default cma area!
[ 2.587780] rkisp rkisp-vir0: rkisp driver version: v02.00.00
[ 2.590008] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 2.617534] rockchip-csi2-dphy-hw ff3e8000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 2.640496] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 2.684553] sc4336 4-0030-1: driver version: 00.01.01
[ 2.684861] sc4336 4-0030-1: Failed to get reset-gpios
[ 2.685832] sc4336 4-0030-1: could not get default pinstate
[ 2.685850] sc4336 4-0030-1: could not get sleep pinstate
[ 2.685885] sc4336 4-0030-1: supply avdd not found, using dummy regulator
[ 2.686894] sc4336 4-0030-1: supply dovdd not found, using dummy regulator
[ 2.687060] sc4336 4-0030-1: supply dvdd not found, using dummy regulator
[ 2.701844] sc4336 4-0030-1: Unexpected sensor id(000000), ret(-5)
[ 2.722571] sc3336 4-0030: driver version: 00.01.01
[ 2.722663] sc3336 4-0030: Failed to get reset-gpios
[ 2.723001] sc3336 4-0030: could not get default pinstate
[ 2.723017] sc3336 4-0030: could not get sleep pinstate
[ 2.723041] sc3336 4-0030: supply avdd not foStarting sshd: und, using dummy regulator
[ 2.724016] sc3336 4-0030: supply dovdd not found, using dummy regulator
[ 2.724378] sc3336 4-0030: supply dvdd not found, using dummy regulator
[ 2.738472] sc3336 4-0030: Unexpected sensor id(000000), ret(-5)
[ 2.759419] sc530ai 4-0030-2: driver version: 00.01.01
[ 2.759468] sc530ai 4-0030-2: lane_num = 2
[ 2.759773] sc530ai 4-0030-2: Failed to get reset-gpios
[ 2.759836] sc530ai 4-0030-2: could not get default pinstate
[ 2.759847] sc530ai 4-0030-2: could not get sleep pinstate
[ 2.759873] sc530ai 4-0030-2: supply avdd not found, using dummy regulator
[ 2.760823] sc530ai 4-0030-2: supply dovdd not found, using dummy regulator
[ 2.761330] sc530ai 4-0030-2: supply dvdd not found, using dummy regulator
[ 2.767368] sc530ai 4-0030-2: Unexpected sensor id(000000), ret(-5)
[ 2.769866] rkcif rkcif-mipi-lvds: clear unready subdev num: 3
[ 2.769894] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.770900] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.770961] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.770976] rkcif-mipi-lvds: Async subdev notifier completed
[ 2.770986] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.771005] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.771014] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 2.771303] rkisp rkisp-vir0: clear unready subdev num: 1
[ 2.771486] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.771531] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.771602] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 2.773174] rkisp-vir0: Async subdev notifier completed
[ 2.811756] rga: rga2, irq = 42, match scheduler
[ 2.813184] rga: rga2 hardware loaded successfully, hw_version:3.3.87975.
[ 2.813209] rga: rga2 probe successfully
[ 2.814181] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ 2.815712] rga: Module initialized. v1.2.23
[ 2.908795] mpp_vcodec: loading out-of-tree module taints kernel.
[ 2.930580] mpp_vcodec: init new
[ 2.931184] mpp_service mpp-srv: 3760314f author: Zhihua Wang 2023-01-12 [vcodec]: check chan create when destroy
[ 2.931205] mpp_service mpp-srv: probe start
[ 2.936105] mpp_rkvenc_540c ffa50000.rkvenc: probing start
[ 2.937013] mpp_rkvenc_540c ffa50000.rkvenc: probing finish
[ 2.937507] mpp_vepu_pp ffa60000.rkvenc-pp: probe device
[ 2.937617] mpp_vepu_pp ffa60000.rkvenc-pp: shared_rst_a_pp is not found!
[ 2.937632] vepu_pp_init:528: No aclk reset resource define
[ 2.937642] mpp_vepu_pp ffa60000.rkvenc-pp: shared_rst_h_pp is not found!
[ 2.937649] vepu_pp_init:531: No hclk reset resource define
[ 2.939798] mpp_vepu_pp ffa60000.rkvenc-pp: probing finish
[ 2.940090] mpp_service mpp-srv: probe success
[ 2.969122] RKNPU ff660000.npu: RKNPU: rknpu iommu device-tree entry not foOK
und!, using non-iommu mode
[ 2.970315] RKNPU ff660000.npu: RKNPU: Initialized RKNPU driver: v0.8.2 for 20220829
[ 2.970425] RKNPU ff660000.npu: dev_pm_opp_set_regulators: no regulator (rknpu) found: -19
Starting telnetd: OK
rmmod: can't unload module 'sc530ai': No such file or directory
/etc/init.d/S50usbdevice: line 144: can't open : no such file
Debug: configfs_init
[ 3.236884] rockit_load start
/
insmod_ko.sh: line 78: /oem/usr/ko/insmod_wifi.sh: not found
ln: /usr/www/userdata: No such file or directory
ln: /usr/www/usb0: No such file or directory
ln: /usr/www/sdcard: No such file or directory
[ 3.264806] rockit_load end
[ 3.336285] file system registered
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
[ 3.421962] using random self ethernet address
[ 3.421997] using random host ethernet address
md5sum: can't open '/tmp/rkipc-factory-config.ini': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/acm.gs6': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mass_storage.0': No such file or directory
Error: not found rkipc.ini !!!
/oem/usr/bin/RkLunch.sh: exit: line 118: Illegal number: -1
[ 3.609680] rk_gmac-dwmac ffa80000.ethernet eth0: PHY [stmmac-0:02] driver [RK630 PHY] (irq=POLL)
[ 3.610145] dwmac4: Master AXI performs any burst length
[ 3.610179] rk_gmac-dwmac ffa80000.ethernet eth0: No Safety Features support found
[ 3.610199] rk_gmac-dwmac ffa80000.ethernet eth0: PTP not supported by HW
[ 3.610509] rk_gmac-dwmac ffa80000.ethernet eth0: configuring for phy/rmii link mode
[ 3.773191] read descriptors
[ 3.773351] read strings
[ 4.772190] usb0: HOST MAC a6:fb:9f:6f:e0:c7
[ 4.772215] usb0: MAC 1e:bb:aa:f5:fd:95
[ 4.881672] dwc3 ffb00000.usb: device reset
[ 4.982760] android_work: sent uevent USB_STATE=CONNECTED
[ 4.995480] android_work: sent uevent USB_STATE=CONFIGURED
current_ip = 172.32.0.70
TARGET_IP = 172.32.0.93
luckfox : set usb0 ip
172.32.0.93
usb0 config success
Starting SMB services: OK
Starting NMB services: OK
/root/main.py and /root/boot.py not exist ,pass...
OK
Welcome to luckfox pico
luckfox login:
