RTL8723bs 连接网络问题

  • zg002
    Posts: 5
    Joined: 2024-10-26 6:58

    完整的日志

    Code: Select all

    [root@luckfox ko]# wpa_supplicant -d -c /etc/wpa_supplicant.conf -i wlan0
wpa_supplicant v2.6
random: Trying to read entropy from /dev/random
Successfully initialized wpa_supplicant
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='0'
ap_scan=1
Priority group 5
   id=0 ssid='luck'
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:6
nl80211: Using driver-based off-channel TX
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Subscribe to mgmt frames with non-AP handle 0x90ba8
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0500
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
netlink: Operstate: ifindex=3 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface wlan0 to a new radio phy0
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 20 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
wlan0: Own MAC address: 2c:c3:e6:57:a8:a8
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=3 (wlan0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wlan0: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
wlan0: Setting scan request: 0.100000 sec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
ctrl_interface_group=0
wlan0: Added interface wlan0
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: ifi_index=3 ifname=wlan0 operstate=2 linkmode=1 ifi_family=0 ifi_flags=0x1003 ([UP])
wlan0: State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=4):
     6c 75 63 6b                                       luck
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x90be0
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x90be0 after 0.006270 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
wlan0: Own scan request started a scan in 0.011278 seconds
EAPOL: disable timer tick
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID 'luck'
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 1.366118 seconds
nl80211: Received scan results (18 BSSes)
wlan0: BSS: Start scan result update 1
wlan0: BSS: Add new id 0 BSSID b8:f8:83:8a:c9:93 SSID 'TP-LINK_C993' freq 2412
wlan0: BSS: Add new id 1 BSSID 1a:44:59:65:66:33 SSID 'Wui' freq 2462
wlan0: BSS: Add new id 2 BSSID b6:8f:18:95:42:c0 SSID 'luck' freq 2437
wlan0: BSS: Add new id 3 BSSID 6a:94:59:99:60:35 SSID 'One Plus' freq 2437
wlan0: BSS: Add new id 4 BSSID d4:b1:10:97:18:f4 SSID 'ChinaNet-cJ4S' freq 2442
wlan0: BSS: Add new id 5 BSSID 16:e5:03:7f:d2:c8 SSID 'iQOO 10' freq 2437
wlan0: BSS: Add new id 6 BSSID d4:b1:10:97:19:0c SSID 'ChinaNet-lCRV' freq 2452
wlan0: BSS: Add new id 7 BSSID 2e:2b:a6:b3:48:f4 SSID 'WYXY-CMCC' freq 2437
wlan0: BSS: Add new id 8 BSSID 2e:2b:a6:b3:48:f3 SSID 'WYXY-ChinaNet' freq 2437
wlan0: BSS: Add new id 9 BSSID ce:2b:a6:b3:48:ed SSID 'WYXY-ChinaNet' freq 2462
wlan0: BSS: Add new id 10 BSSID ce:2b:a6:b3:48:ee SSID 'WYXY-CMCC' freq 2462
wlan0: BSS: Add new id 11 BSSID ce:2b:a6:b3:45:5e SSID 'WYXY-CMCC' freq 2462
wlan0: BSS: Add new id 12 BSSID 8e:2b:a6:b2:d9:fa SSID 'WYXY-CMCC' freq 2437
wlan0: BSS: Add new id 13 BSSID ce:2b:a6:b3:45:5d SSID 'WYXY-ChinaNet' freq 2462
wlan0: BSS: Add new id 14 BSSID 8e:2b:a6:b2:d9:f9 SSID 'WYXY-ChinaNet' freq 2437
wlan0: BSS: Add new id 15 BSSID 6e:2b:a6:b3:4f:77 SSID 'WYXY-ChinaNet' freq 2462
wlan0: BSS: Add new id 16 BSSID 6e:2b:a6:b3:4f:78 SSID 'WYXY-CMCC' freq 2462
wlan0: BSS: Add new id 17 BSSID ce:2b:a6:b3:49:4d SSID 'WYXY-ChinaNet' freq 2412
BSS: last_scan_res_used=18/32
wlan0: New scan results available (own=1 ext=0)
wlan0: Radio work 'scan'@0x90be0 done in 1.959739 seconds
wlan0: radio_work_free('scan'@0x90be0: num_active_works --> 0
wlan0: Selecting BSS from priority group 5
wlan0: 0: b8:f8:83:8a:c9:93 ssid='TP-LINK_C993' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-45 freq=2412
wlan0:    skip - SSID mismatch
wlan0: 1: 1a:44:59:65:66:33 ssid='Wui' wpa_ie_len=0 rsn_ie_len=20 caps=0x411 level=-47 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 2: b6:8f:18:95:42:c0 ssid='luck' wpa_ie_len=0 rsn_ie_len=20 caps=0x1431 level=-47 freq=2437
wlan0:    selected based on RSN IE
wlan0:    selected BSS b6:8f:18:95:42:c0 ssid='luck'
wlan0: Considering connect request: reassociate: 0  selected: b6:8f:18:95:42:c0  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x91a98  current_ssid=(nil)
wlan0: Request association with b6:8f:18:95:42:c0
wlan0: Add radio work 'connect'@0x90be0
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'connect'@0x90be0 after 0.006294 second wait
wlan0: Trying to associate with b6:8f:18:95:42:c0 (SSID='luck' freq=2437 MHz)
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=0x91a98 try_opportunistic=0
RSN: Search for BSSID b6:8f:18:95:42:c0
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 0c 00
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: State: SCANNING -> ASSOCIATING
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
Limit connection to BSSID b6:8f:18:95:42:c0 freq=2437 MHz based on scan results (bssid_set=0)
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Unsubscribe mgmt frames handle 0x88818321 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x90ba8
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0500
nl80211: Connect (ifindex=3)
  * bssid=b6:8f:18:95:42:c0
  * bssid_hint=b6:8f:18:95:42:c0
  * freq=2437
  * freq_hint=2437
  * SSID - hexdump_ascii(len=4):
     6c 75 63 6b                                       luck
  * IEs - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
  * WPA Versions 0x2
  * pairwise=0xfac04
  * group=0xfac04
  * akm=0xfac02
  * Auth Type 0
[ 2230.404252] RTL8723BS: rtw_set_802_11_connect(wlan0)  fw_state = 0x00000008
nl80211: Connect request send successfully
wlan0: Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
nl80211: Drv Event 46 (NL80211_CMD_CONNECT) received for wlan0
nl80211: Connect event (status=1 ignore_next_local_disconnect=0)
wlan0: Event ASSOC_REJECT (13) received
wlan0: CTRL-EVENT-ASSOC-REJECT status_code=1
wlan0: Radio work 'connect'@0x90be0 done in 6.676580 seconds
wlan0: radio_work_free('connect'@0x90be0: num_active_works --> 0
Added BSSID b6:8f:18:95:42:c0 into blacklist
wlan0: Blacklist count 1 --> request scan in 100 ms
wlan0: Setting scan request: 0.100000 sec
wlan0: State: ASSOCIATING -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
nl80211: Drv Event 46 (NL80211_CMD_CONNECT) received for wlan0
nl80211: Connect event (status=1 ignore_next_local_disconnect=0)
wlan0: Event ASSOC_REJECT (13) received
wlan0: CTRL-EVENT-ASSOC-REJECT status_code=1
Added BSSID 00:00:00:00:00:00 into blacklist
wlan0: Blacklist count 1 --> request scan in 100 ms
wlan0: Ignore new scan request for 0.100000 sec since an earlier request is scheduled to trigger sooner
wlan0: State: DISCONNECTED -> DISCONNECTED
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wlan0: State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=4):
     6c 75 63 6b                                       luck
wlan0: Starting AP scan for wildcard SSID
wlan0: Add radio work 'scan'@0x963f8
wlan0: First radio work item in the queue - schedule start immediately
wlan0: Starting radio work 'scan'@0x963f8 after 0.006273 second wait
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
wlan0: Own scan request started a scan in 0.012132 seconds
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan probed for SSID 'luck'
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472
wlan0: Event SCAN_RESULTS (3) received
wlan0: Scan completed in 1.359321 seconds
nl80211: Received scan results (20 BSSes)
wlan0: BSS: Start scan result update 2
wlan0: BSS: Add new id 18 BSSID 6e:2b:a6:b2:fb:17 SSID 'WYXY-ChinaNet' freq 2412
wlan0: BSS: Add new id 19 BSSID ce:2b:a6:b3:49:4e SSID 'WYXY-CMCC' freq 2412
BSS: last_scan_res_used=20/32
wlan0: New scan results available (own=1 ext=0)
wlan0: Radio work 'scan'@0x963f8 done in 1.428447 seconds
wlan0: radio_work_free('scan'@0x963f8: num_active_works --> 0
wlan0: Selecting BSS from priority group 5
wlan0: 0: b8:f8:83:8a:c9:93 ssid='TP-LINK_C993' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-45 freq=2412
wlan0:    skip - SSID mismatch
wlan0: 1: b6:8f:18:95:42:c0 ssid='luck' wpa_ie_len=0 rsn_ie_len=20 caps=0x1431 level=-47 freq=2437
wlan0:    skip - blacklisted (count=1 limit=0)
wlan0: 2: 1a:44:59:65:66:33 ssid='Wui' wpa_ie_len=0 rsn_ie_len=20 caps=0x411 level=-48 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 3: 6a:94:59:99:60:35 ssid='One Plus' wpa_ie_len=0 rsn_ie_len=20 caps=0x411 level=-64 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 4: 16:e5:03:7f:d2:c8 ssid='iQOO 10' wpa_ie_len=0 rsn_ie_len=20 caps=0x1431 level=-65 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 5: d4:b1:10:97:18:f4 ssid='ChinaNet-cJ4S' wpa_ie_len=22 rsn_ie_len=0 caps=0x411 level=-61 freq=2442
wlan0:    skip - SSID mismatch
wlan0: 6: d4:b1:10:97:19:0c ssid='ChinaNet-lCRV' wpa_ie_len=22 rsn_ie_len=0 caps=0x411 level=-67 freq=2452
wlan0:    skip - SSID mismatch
wlan0: 7: 2e:2b:a6:b3:48:f4 ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-45 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 8: 2e:2b:a6:b3:48:f3 ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-45 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 9: ce:2b:a6:b3:48:ed ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-49 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 10: ce:2b:a6:b3:48:ee ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-49 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 11: ce:2b:a6:b3:45:5e ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-59 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 12: 8e:2b:a6:b2:d9:fa ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-59 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 13: 8e:2b:a6:b2:d9:f9 ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-60 freq=2437
wlan0:    skip - SSID mismatch
wlan0: 14: ce:2b:a6:b3:45:5d ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-60 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 15: 6e:2b:a6:b3:4f:77 ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-61 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 16: 6e:2b:a6:b3:4f:78 ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-61 freq=2462
wlan0:    skip - SSID mismatch
wlan0: 17: 6e:2b:a6:b2:fb:17 ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-64 freq=2412
wlan0:    skip - SSID mismatch
wlan0: 18: ce:2b:a6:b3:49:4e ssid='WYXY-CMCC' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-65 freq=2412
wlan0:    skip - SSID mismatch
wlan0: 19: ce:2b:a6:b3:49:4d ssid='WYXY-ChinaNet' wpa_ie_len=0 rsn_ie_len=0 caps=0x521 level=-65 freq=2412
wlan0:    skip - SSID mismatch
wlan0: No APs found - clear blacklist and try again
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)
Removed BSSID b6:8f:18:95:42:c0 from blacklist (clear)
wlan0: Selecting BSS from priority group 5
wlan0: 0: b8:f8:83:8a:c9:93 ssid='TP-LINK_C993' wpa_ie_len=26 rsn_ie_len=24 caps=0x411 level=-45 freq=2412
wlan0:    skip - SSID mismatch
wlan0: 1: b6:8f:18:95:42:c0 ssid='luck' wpa_ie_len=0 rsn_ie_len=20 caps=0x1431 level=-47 freq=2437
wlan0:    selected based on RSN IE
wlan0:    selected BSS b6:8f:18:95:42:c0 ssid='luck'
wlan0: Considering connect request: reassociate: 0  selected: b6:8f:18:95:42:c0  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING  ssid=0x91a98  current_ssid=(nil)
wlan0: Request association with b6:8f:18:95:42:c0
wlan0: Re-association to the same ESS
wlan0: Add radio work 'connect'@0x963f8
wlan0: First radio work item in the queue - schedule start immediately
RSN: Ignored PMKID candidate without preauth flag
wlan0: Starting radio work 'connect'@0x963f8 after 0.010711 second wait
wlan0: Trying to associate with b6:8f:18:95:42:c0 (SSID='luck' freq=2437 MHz)
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
RSN: PMKSA cache search - network_ctx=0x91a98 try_opportunistic=0
RSN: Search for BSSID b6:8f:18:95:42:c0
RSN: No PMKSA cache entry found
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 0c 00
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: State: SCANNING -> ASSOCIATING
nl80211: Set wlan0 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=3 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
Limit connection to BSSID b6:8f:18:95:42:c0 freq=2437 MHz based on scan results (bssid_set=0)
nl80211: Set mode ifindex 3 iftype 2 (STATION)
nl80211: Unsubscribe mgmt frames handle 0x88818321 (mode change)
nl80211: Subscribe to mgmt frames with non-AP handle 0x90ba8
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a07
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0a11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1101
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=1102
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0505
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x90ba8 match=0500
nl80211: Connect (ifindex=3)
  * bssid=b6:8f:18:95:42:c0
  * bssid_hint=b6:8f:18:95:42:c0
  * freq=2437
  * freq_hint=2437
  * SSID - hexdump_ascii(len=4):
     6c 75 63 6b                                       luck
  * IEs - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
  * WPA Versions 0x2
  * pairwise=0xfac04
  * group=0xfac04
  * akm=0xfac02
  * Auth Type 0
  • User avatar
    Alenwowo
    Posts: 129
    Joined: 2024-10-10 1:11

    你这个是自己买的wifi模块吗？
  • zg002
    Posts: 5
    Joined: 2024-10-26 6:58

    Alenwowo wrote: ↑2024-10-26 8:16 你这个是自己买的wifi模块吗？
    是的，模块是RTL8723BS SD 卡形状模块
  • User avatar
    Alenwowo
    Posts: 129
    Joined: 2024-10-10 1:11

    zg002 wrote: ↑2024-10-26 8:40
    Alenwowo wrote: ↑2024-10-26 8:16 你这个是自己买的wifi模块吗？
    是的，模块是RTL8723BS SD 卡形状模块
    我们开发板使用的是aic8800模块，建议您使用这个。
  • zg002
    Posts: 5
    Joined: 2024-10-26 6:58

    Alenwowo wrote: ↑2024-10-26 8:58
    zg002 wrote: ↑2024-10-26 8:40
    Alenwowo wrote: ↑2024-10-26 8:16 你这个是自己买的wifi模块吗？
    是的，模块是RTL8723BS SD 卡形状模块
    我们开发板使用的是aic8800模块，建议您使用这个。
    我找到问题了，我将设备树中的max-frequency调低，发现可以正常连接网络。可能速度太高容易干扰
  • User avatar
    Alenwowo
    Posts: 129
    Joined: 2024-10-10 1:11

    zg002 wrote: ↑2024-10-28 15:28
    Alenwowo wrote: ↑2024-10-26 8:58
    zg002 wrote: ↑2024-10-26 8:40
    是的，模块是RTL8723BS SD 卡形状模块
    我们开发板使用的是aic8800模块，建议您使用这个。
    我找到问题了，我将设备树中的max-frequency调低，发现可以正常连接网络。可能速度太高容易干扰
    好的
    • Post Reply

    Return to “LuckFox Pico”