启动串口输出日志如下：
DDR 306b9977f5 wesley.yao 23/12/21-09:28:37,fwver: v1.15
S5P1
4x
f967
rgef1
DDRConf2
DDR3, BW=16 Col=10 Bk=8 CS0 Row=14 CS=1 Size=256MB
924MHz
DDR bin out
U-Boot SPL board init
U-Boot SPL 2017.09 (Dec 11 2025 - 16:55:22)
unknown raw ID 0 0 0
Trying to boot from MMC2
Card did not respond to voltage select!
mmc_init: -95, time 20
Card did not respond to voltage select!
mmc_init: -95, time 20
spl: mmc init failed with error: -95 | Minicom 2.8 | VT102 | 脱机 | ttyUSB0
Trying to boot from MMC1
Best phase range 270-237 (30 len)
Successfully tuned phase to 79, used 3ms
ENVF: Primary 0x00000000 - 0x00008000
ENVF: Primary 0x00000000 - 0x00008000
No misc partition
Trying fit image at 0x440 sector
## Verified-boot: 0
## Checking uboot 0x00200000 (lzma @0x00400000) ... sha256(9d5d780d93...) + sha256(a33750cc52...) + OK
## Checking fdt 0x00261170 ... sha256(9f596c5683...) + OK
Total: 382.224/416.572 ms
Jumping to U-Boot(0x00200000)
U-Boot 2017.09 (Dec 11 2025 - 16:55:22 +0800)
Model: Rockchip RV1106 EVB Board
MPIDR: 0xf00
PreSerial: 2, raw, 0xff4c0000
DRAM: 256 MiB
Sysmem: init
Relocation Offset: 0fd80000
Relocation fdt: 0edf9f58 - 0edfede8
CR: M/C/I
Using default environment
mmc@ffa90000: 0, mmc@ffaa0000: 1
Best phase range 270-237 (30 len)
Successfully tuned phase to 79, used 3ms
ENVF: Primary 0x00000000 - 0x00008000
ENVF: Primary 0x00000000 - 0x00008000
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: ENV
DM: v2
No misc partition
boot mode: None
RESC: 'boot', blk@0x00001fa9
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
Model: Luckfox Pico Pi W
## retrieving sd_update.txt ...
Card did not respond to voltage select!
mmc_init: -95, time 20
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 924000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
aclk_peri_root 400000 KHz
hclK_peri_root 200000 KHz
pclk_peri_root 100000 KHz
aclk_bus_root 300000 KHz
pclk_top_root 100000 KHz
pclk_pmu_root 100000 KHz
hclk_pmu_root 200000 KHz
Net: eth0: ethernet@ffa80000
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image at 0xe8cbb00 with size 0x0032d306
Fdt Ramdisk skip relocation
No misc partition
Sysmem Warn: kernel 'reserved-memory' "mmc@3f000"(0x0003f000 - 0x00040000) is overlap with "KERNEL" (0x00008000 - 0x0032b204)
sysmem_dump_all:
--------------------------------------------------------------------
memory.rgn[0].addr = 0x00000000 - 0x10000000 (size: 0x10000000)
memory.total = 0x10000000 (256 MiB. 0 KiB)
--------------------------------------------------------------------
allocated.rgn[0].name = "UBOOT"
.addr = 0x0edf9f30 - 0x10000000 (size: 0x012060d0)
allocated.rgn[1].name = "STACK"
.addr = 0x0ebf9f30 - 0x0edf9f30 (size: 0x00200000)
allocated.rgn[2].name = "FIT"
.addr = 0x0e8cbb00 - 0x0ebf8f04 (size: 0x0032d404)
allocated.rgn[3].name = "FDT"
.addr = 0x00c00000 - 0x00c09804 (size: 0x00009804)
allocated.rgn[4].name = "KERNEL"
.addr = 0x00008000 - 0x0032b204 (size: 0x00323204)
kmem-resv.rgn[0].name = "mmc@3f000"
.addr = 0x0003f000 - 0x00040000 (size: 0x00001000)
framework malloc_r = 16 MiB
framework malloc_f = 512 KiB
allocated.total = 0x01a60edc (26 MiB. 387 KiB)
--------------------------------------------------------------------
LMB.allocated[0].addr = 0x00008000 - 0x0032b204 (size: 0x00323204)
LMB.allocated[1].addr = 0x00c00000 - 0x00c09804 (size: 0x00009804)
LMB.allocated[2].addr = 0x0e8cbb00 - 0x0ebf8f40 (size: 0x0032d440)
LMB.allocated[3].addr = 0x0ebf9f30 - 0x10000000 (size: 0x014060d0)
reserved.core.total = 0x01a5ff18 (26 MiB. 383 KiB)
--------------------------------------------------------------------
## Loading kernel from FIT Image at 0e8cbb00 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0x0e8d5b00
Data Size: 3289448 Bytes = 3.1 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00008000
Entry Point: 0x00008000
Hash algo: sha256
Hash value: c3a5e4fbfdf2ca62c57618880da2b1b0dfb6e26cc802b831d0d83d7ccd15918a
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 0e8cbb00 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x0e8cc300
Data Size: 38525 Bytes = 37.6 KiB
Architecture: ARM
Load Address: 0x00c00000
Hash algo: sha256
Hash value: 65daa0fb53bfafabc7f7da3eb694c0c541949ed005aba43fba6225f5197faa2d
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0e8cbb00 to 0x00c00000
Booting using the fdt blob at 0x00c00000
Loading Kernel Image from 0x0e8d5b00 to 0x00008000 ... OK
kernel loaded at 0x00008000, end = 0x0032b168
Using Device Tree in place at 00c00000, end 00c0c67c
## reserved-memory:
mmc@3f000: addr=3f000 size=1000
Adding bank: 0x00000000 - 0x10000000 (size: 0x10000000)
Total: 782.740/1204.385 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.160 (zhuhs@zhuhs-pc) (arm-rockchip830-linux-uclibcgnueabihf-gcc (crosstool-NG 1.24.0) 8.3.0, GNU ld (crosstool-NG 1.25
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c53c7d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Luckfox Pico Pi W
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 67584 KiB at 0x0be00000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: user_debug=31 storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal rootwait earlycon=uart8250,m5
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 184952K/262144K available (4135K kernel code, 399K rwdata, 2008K rodata, 200K init, 147K bss, 9608K reserved, 67584K cma-reserve)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000017] Switching to timer-based delay loop, resolution 41ns
[ 0.000492] Console: colour dummy device 80x30
[ 0.000532] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000549] pid_max: default: 4096 minimum: 301
[ 0.000704] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.000718] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001258] CPU: Testing write buffer coherency: ok
[ 0.001800] Setting up static identity map for 0x81c0 - 0x81f8
[ 0.002274] devtmpfs: initialized
[ 0.009190] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.009343] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.009362] futex hash table entries: 16 (order: -5, 192 bytes, linear)
[ 0.009436] pinctrl core: initialized pinctrl subsystem
[ 0.010555] NET: Registered protocol family 16
[ 0.010997] DMA: failed to allocate 0 KiB pool for atomic coherent allocation
[ 0.011500] Registered FIQ tty driver
[ 0.011808] thermal_sys: Registered thermal governor 'step_wise'
[ 0.011815] thermal_sys: Registered thermal governor 'user_space'
[ 0.012029] cpuidle: using governor menu
[ 0.025753] rockchip-gpio ff380000.gpio: probed /pinctrl/gpio@ff380000
[ 0.026384] rockchip-gpio ff530000.gpio: probed /pinctrl/gpio@ff530000
[ 0.026964] rockchip-gpio ff540000.gpio: probed /pinctrl/gpio@ff540000
[ 0.027648] rockchip-gpio ff550000.gpio: probed /pinctrl/gpio@ff550000
Seeding 256 bits and crediting
[ 0.028243] rockchip-gpio ff560000.gpio: probed /pinctrl/gpio@ff560000
Saving 256 bits of creditable seed for next boot
[ 0.028325] rockchip-pinctrl pinctrl: probed pinctrl
Starting syslogd: OK
[ 0.038802] fiq_debugger fiq_debugger.0: IRQ uart_irq not found
Starting klogd: [ 0.038825] fiq_debugger fiq_debugger.0: IRQ wakeup not found
OK
[ 0.039077] printk: console [ttyFIQ0] enabled
[ 0.039246] Registered fiq debugger ttyFIQ0
[ 0.040369] reg-fixed-voltage vdd-arm: Fixed regulator specified with variable voltages
Running sysctl: [ 0.040398] reg-fixed-voltage: probe of vdd-arm failed with error -22
[ 0.040984] SCSI subsystem initialized
[ 0.041188] usbcore: registered new interface driver usbfs
[ 0.041237] usbcore: registered new interface driver hub
[ 0.041283] usbcore: registered new device driver usb
[ 0.041494] mc: Linux media interface: v0.10
[ 0.041532] videodev: Linux video capture interface: v2.00
[ 0.042579] Advanced Linux Sound Architecture Driver Initialized.
[ 0.043060] Bluetooth: Core ver 2.22
OK
[ 0.043124] NET: Registered protocol family 31
[ 0.043136] Bluetooth: HCI device and connection manager initialized
[ 0.043151] Bluetooth: HCI socket layer initialized
Populating /dev using udev: [ 0.043163] Bluetooth: L2CAP socket layer initialized
[ 0.043186] Bluetooth: SCO socket layer initialized
[ 0.043610] rockchip-cpuinfo cpuinfo: SoC : 11061000
[ 0.043633] rockchip-cpuinfo cpuinfo: Serial : f3faf22276ecf26e
[ 0.043995] rockchip,rknpor-powergood ff000000.syscon:rknpor-powergood: probe success!
[ 0.044846] clocksource: Switched to clocksource arch_sys_counter
[ 0.050799] NET: Registered protocol family 2
[ 0.051018] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.051459] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.051491] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.051516] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.051539] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.051625] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.051652] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.051776] NET: Registered protocol family 1
[ 0.052255] RPC: Registered named UNIX socket transport module.
[ 0.052273] RPC: Registered udp transport module.
[ 0.052280] RPC: Registered tcp transport module.
[ 0.052287] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.053162] rockchip-thermal ff3c8000.tsadc: tsadc is probed successfully!
[ 0.054157] Initialise system trusted keyrings
[ 0.054392] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.057842] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.058571] NFS: Registering the id_resolver key type
[ 0.058672] Key type id_resolver registered
[ 0.058681] Key type id_legacy registered
[ 0.058725] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.144068] Key type asymmetric registered
[ 0.144090] Asymmetric key parser 'x509' registered
[ 0.144111] io scheduler mq-deadline registered
[ 0.144474] rockchip-usb2phy ff3e0000.usb2-phy: IRQ index 0 not found
[ 0.148593] dma-pl330 ff420000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 0.148624] dma-pl330 ff420000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 0.149368] rockchip-pvtm ff240000.pvtm: pvtm@0 probed
[ 0.149553] rockchip-pvtm ff390000.pvtm: pvtm@0 probed
[ 0.149861] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 0.150367] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 0.150966] ff4b0000.serial: ttyS1 at MMIO 0xff4b0000 (irq = 36, base_baud = 1500000) is a 16550A
[ 0.156790] random: crng init done
[ 0.164223] brd: module loaded
[ 0.169265] loop: module loaded
[ 0.171212] rk_gmac-dwmac ffa80000.ethernet: IRQ eth_lpi not found
[ 0.171374] rk_gmac-dwmac ffa80000.ethernet: PTP uses main clock
[ 0.171418] rk_gmac-dwmac ffa80000.ethernet: no regulator found
[ 0.171431] rk_gmac-dwmac ffa80000.ethernet: clock input or output? (input).
[ 0.171441] rk_gmac-dwmac ffa80000.ethernet: Can not read property: tx_delay.
[ 0.171450] rk_gmac-dwmac ffa80000.ethernet: set tx_delay to 0xffffffff
[ 0.171459] rk_gmac-dwmac ffa80000.ethernet: Can not read property: rx_delay.
[ 0.171467] rk_gmac-dwmac ffa80000.ethernet: set rx_delay to 0xffffffff
[ 0.171567] rk_gmac-dwmac ffa80000.ethernet: integrated PHY? (yes).
[ 0.171584] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_rx
[ 0.171596] rk_gmac-dwmac ffa80000.ethernet: cannot get clock mac_clk_tx
[ 0.171626] rk_gmac-dwmac ffa80000.ethernet: cannot get clock clk_mac_speed
[ 0.171636] rk_gmac-dwmac ffa80000.ethernet: clock input from PHY
[ 0.171881] rk_gmac-dwmac ffa80000.ethernet: init for RMII
[ 0.172071] rk_gmac-dwmac ffa80000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 0.172091] rk_gmac-dwmac ffa80000.ethernet: DWMAC4/5
[ 0.172104] rk_gmac-dwmac ffa80000.ethernet: DMA HW capability register supported
[ 0.172113] rk_gmac-dwmac ffa80000.ethernet: RX Checksum Offload Engine supported
[ 0.172122] rk_gmac-dwmac ffa80000.ethernet: TX Checksum insertion supported
[ 0.172130] rk_gmac-dwmac ffa80000.ethernet: Wake-Up On Lan supported
[ 0.172136] rk_gmac-dwmac ffa80000.ethernet: TSO supported
[ 0.172144] rk_gmac-dwmac ffa80000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 0.172152] rk_gmac-dwmac ffa80000.ethernet: TSO feature enabled
[ 0.172162] rk_gmac-dwmac ffa80000.ethernet: Using 40 bits DMA width
[ 0.174341] PPP generic driver version 2.4.2
[ 0.174626] PPP BSD Compression module registered
[ 0.174640] PPP Deflate Compression module registered
[ 0.174705] usbcore: registered new interface driver asix
[ 0.174753] usbcore: registered new interface driver ax88179_178a
[ 0.174785] usbcore: registered new interface driver cdc_ether
[ 0.174829] usbcore: registered new interface driver net1080
[ 0.174906] usbcore: registered new interface driver rndis_host
[ 0.174941] usbcore: registered new interface driver cdc_subset
[ 0.174981] usbcore: registered new interface driver zaurus
[ 0.175036] usbcore: registered new interface driver cdc_ncm
[ 0.175071] usbcore: registered new interface driver qmi_wwan
[ 0.178931] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.179282] phy phy-ff3e0000.usb2-phy.0: illegal mode
[ 0.179301] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 0.179334] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 0.179512] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000022010010
[ 0.179556] xhci-hcd xhci-hcd.0.auto: irq 64, io mem 0xffb00000
[ 0.180576] hub 1-0:1.0: USB hub found
[ 0.180636] hub 1-0:1.0: 1 port detected
[ 0.180958] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 0.180989] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 0.181010] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 0.181108] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.181681] hub 2-0:1.0: USB hub found
[ 0.181732] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 0.182062] usbcore: registered new interface driver cdc_wdm
[ 0.182149] usbcore: registered new interface driver usb-storage
[ 0.182273] usbcore: registered new interface driver usb_ch343
[ 0.182287] ch343: USB serial driver for ch342/ch343/ch344/ch347/ch9101/ch9102/ch9103/ch9104, etc.
[ 0.182295] ch343: V1.5 On 2022.12
[ 0.182332] usbcore: registered new interface driver option
[ 0.182360] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.182496] usbcore: registered new interface driver qcserial
[ 0.182526] usbserial: USB Serial support registered for Qualcomm USB modem
[ 0.182682] gadgetfs: USB Gadget filesystem, version 24 Aug 2004
[ 0.182698] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers
[ 0.183745] rtc rtc0: invalid alarm value: 2202-11-01T11:28:72
[ 0.184107] rockchip-rtc ff1c0000.rtc: registered as rtc0
[ 0.184179] rockchip-rtc ff1c0000.rtc: setting system clock to 2021-01-01T19:48:49 UTC (1609530529)
[ 0.184396] i2c /dev entries driver
[ 0.186702] usbcore: registered new interface driver uvcvideo
[ 0.186721] USB Video Class driver (1.1.1)
[ 0.187270] Bluetooth: HCI UART driver ver 2.3
[ 0.187288] Bluetooth: HCI UART protocol H4 registered
[ 0.187458] cpu cpu0: leakage=16
[ 0.188210] Synopsys Designware Multimedia Card Interface Driver
[ 0.189058] dtbocfg: 0.1.0
[ 0.189101] dtbocfg: OK
[ 0.190333] dwmmc_rockchip ff9a0000.mmc: No normal pinctrl state
[ 0.190359] dwmmc_rockchip ff9a0000.mmc: No idle pinctrl state
[ 0.190549] dwmmc_rockchip ff9a0000.mmc: IDMAC supports 32-bit address mode.
[ 0.190589] dwmmc_rockchip ff9a0000.mmc: Using internal DMA controller.
[ 0.190607] dwmmc_rockchip ff9a0000.mmc: Version ID is 270a
[ 0.190645] dwmmc_rockchip ff9a0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[ 0.191234] dwmmc_rockchip ffa90000.mmc: IDMAC supports 32-bit address mode.
[ 0.191276] dwmmc_rockchip ffa90000.mmc: Using internal DMA controller.
[ 0.191294] dwmmc_rockchip ffa90000.mmc: Version ID is 270a
[ 0.191328] dwmmc_rockchip ffa90000.mmc: DW MMC controller at irq 53,32 bit host data width,256 deep fifo
[ 0.191434] mmc_host mmc0: card is non-removable.
[ 0.191656] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 0.192224] dwmmc_rockchip ffaa0000.mmc: No normal pinctrl state
[ 0.192247] dwmmc_rockchip ffaa0000.mmc: No idle pinctrl state
[ 0.192581] dwmmc_rockchip ffaa0000.mmc: IDMAC supports 32-bit address mode.
[ 0.192620] dwmmc_rockchip ffaa0000.mmc: Using internal DMA controller.
[ 0.192635] dwmmc_rockchip ffaa0000.mmc: Version ID is 270a
[ 0.192672] dwmmc_rockchip ffaa0000.mmc: DW MMC controller at irq 54,32 bit host data width,256 deep fifo
[ 0.192778] dwmmc_rockchip ffaa0000.mmc: allocated mmc-pwrseq
[ 0.192790] mmc_host mmc1: card is non-removable.
[ 0.193515] usbcore: registered new interface driver snd-usb-audio
[ 0.194065] rv1106-acodec ff480000.acodec: current soc_id: rv1106
[ 0.194128] rv1106-acodec ff480000.acodec: No use pa_ctl_gpio and pa_ctl_delay_ms: 0
[ 0.195744] NET: Registered protocol family 17
[ 0.196004] Bluetooth: RFCOMM TTY layer initialized
[ 0.196027] Bluetooth: RFCOMM socket layer initialized
[ 0.196059] Bluetooth: RFCOMM ver 1.11
[ 0.196111] [BT_RFKILL]: Enter rfkill_rk_init
[ 0.196120] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 0.196618] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 5.
[ 0.196660] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 2.
[ 0.196681] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 34.
[ 0.196693] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[ 0.196741] [BT_RFKILL]: Failed to get bt_default_wake_host gpio.
[ 0.196784] rfkill_bt: probe of wireless-bluetooth failed with error -1
[ 0.196864] Key type dns_resolver registered
[ 0.197773] Loading compiled-in X.509 certificates
[ 0.212629] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 0.212790] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 0.225410] input: adc-keys as /devices/platform/adc-keys/input/input0
[ 0.237542] mmc1: queuing unknown CIS tuple 0x10 (5 bytes)
[ 0.242770] mmc_host mmc1: Bus speed (slot 0) = 49500000Hz (slot req 50000000Hz, actual 49500000HZ div = 0)
[ 0.242952] mmc1: queuing unknown CIS tuple 0x10 (5 bytes)
[ 0.244050] mmc1: new SDIO card at address 7a8a
[ 0.245294] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 0.248460] mmc_host mmc0: Bus speed (slot 0) = 49500000Hz (slot req 52000000Hz, actual 49500000HZ div = 0)
[ 0.249444] mmc0: new high speed MMC card at address 0001
[ 0.249861] mmcblk0: mmc0:0001 AT2S38 7.23 GiB
[ 0.249960] mmcblk0boot0: mmc0:0001 AT2S38 partition 1 4.00 MiB
[ 0.250059] mmcblk0boot1: mmc0:0001 AT2S38 partition 2 4.00 MiB
[ 0.250266] mmcblk0rpmb: mmc0:0001 AT2S38 partition 3 4.00 MiB, chardev (247:0)
[ 0.250695] mmcblk0: p1(env) p2(idblock) p3(uboot) p4(boot) p5(oem) p6(userdata) p7(rootfs)
[ 0.278348] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 0.307661] ALSA device list:
[ 0.307689] #0: rv1106-acodec
[ 0.313445] EXT4-fs (mmcblk0p7): INFO: recovery required on readonly filesystem
[ 0.313470] EXT4-fs (mmcblk0p7): write access will be enabled during recovery
[ 0.333148] mmc_host mmc2: Bus speed (slot 0) = 187500Hz (slot req 100000Hz, actual 93750HZ div = 1)
[ 0.367804] EXT4-fs (mmcblk0p7): recovery complete
[ 0.368370] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[ 0.368440] VFS: Mounted root (ext4 filesystem) readonly on device 179:7.
[ 0.368568] devtmpfs: mounted
[ 0.368746] Freeing unused kernel memory: 200K
[ 0.368755] Kernel memory protection not selected by kernel config.
[ 0.368779] Run /sbin/init as init process
[ 0.372539] process '/bin/busybox' started with executable stack
[ 0.424204] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null)
[ 0.464936] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 0.633043] udevd[98]: starting version 3.2.7
[ 0.637694] udevd[98]: specified group 'input' unknown
[ 0.638670] udevd[98]: specified group 'kvm' unknown
[ 0.661405] hub 1-1:1.0: USB hub found
[ 0.661506] hub 1-1:1.0: 4 ports detected
[ 0.661985] udevd[99]: starting eudev-3.2.7
[ 1.004906] usb 1-1.4: new full-speed USB device number 3 using xhci-hcd
[ 1.105024] usb 1-1.4: device descriptor read/64, error -32
[ 1.325472] usb 1-1.4: device descriptor read/64, error -32
[ 1.544882] usb 1-1.4: new full-speed USB device number 4 using xhci-hcd
[ 1.644878] usb 1-1.4: device descriptor read/64, error -32
[ 1.864878] usb 1-1.4: device descriptor read/64, error -32
[ 1.985077] usb 1-1-port4: attempt power cycle
[ 2.644865] usb 1-1.4: new full-speed USB device number 5 using xhci-hcd
[ 2.644985] usb 1-1.4: Device not responding to setup address.
[ 2.864940] usb 1-1.4: Device not responding to setup address.
[ 3.084883] usb 1-1.4: device not accepting address 5, error -71
[ 3.184864] usb 1-1.4: new full-speed USB device number 6 using xhci-hcd
[ 3.184962] usb 1-1.4: Device not responding to setup address.
[ 3.404933] usb 1-1.4: Device not responding to setup address.
[ 3.624858] usb 1-1.4: device not accepting address 6, error -71
done
[ 3.625088] usb 1-1-port4: unable to enumerate USB device
resize2fs 1.46.5 (30-Dec-2021)
The filesystem is already 1572864 (4k) blocks long. Nothing to do!
e2fsck 1.46.5 (30-Dec-2021)
userdata: recovering journal
Setting free blocks count to 243615 (was 243614)
userdata: clean, 13/65536 files, 18529/262144 blocks
[ 3.848764] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ 3.848815] ext4 filesystem being mounted at /userdata supports timestamps until 2038 (0x7fffffff)
resize2fs 1.46.5 (30-Dec-2021)
The filesystem is already 262144 (1k) blocks long. Nothing to do!
tune2fs 1.46.5 (30-Dec-2021)
e2fsck 1.46.5 (30-Dec-2021)
oem: recovering journal
oem: clean, 216/32768 files, 11392/131072 blocks
[ 4.012410] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
resize2fs 1.46.5 (30-Dec-2021)
The filesystem is already 131072 (4k) blocks long. Nothing to do!
tune2fs 1.46.5 (30-Dec-2021)
Initializing random number generator... done.
/dev/block/by-name/userdata on /userdata type ext4 (rw,relatime)
Starting system message bus: [ 4.201670] rk_dvbm ffa70000.rkdvbm: probe start
[ 4.201705] rk_dvbm ffa70000.rkdvbm: dvbm ctx 3529dc3e
[ 4.202449] rk_dvbm ffa70000.rkdvbm: probe success
dbus[169]: Unknown username "pulse" in message bus configuration file
done
Starting bluetoothd: [ 4.244300] sc3336 4-0030: driver version: 00.01.01
[ 4.244403] sc3336 4-0030: Failed to get pwdn-gpios
[ 4.244418] sc3336 4-0030: could not get default pinstate
[ 4.244427] sc3336 4-0030: could not get sleep pinstate
OK
[ 4.244453] sc3336 4-0030: supply avdd not found, using dummy regulator
[ 4.244660] sc3336 4-0030: supply dovdd not found, using dummy regulator
[ 4.244725] sc3336 4-0030: supply dvdd not found, using dummy regulator
[ 4.255684] sc3336 4-0030: Unexpected sensor id(000000), ret(-5)
Starting network: [ 4.277341] mis5001 4-0031: driver version: 00.01.02
[ 4.277440] mis5001 4-0031: Failed to get pwdn-gpios
[ 4.277454] mis5001 4-0031: could not get default pinstate
[ 4.277463] mis5001 4-0031: could not get sleep pinstate
[ 4.277484] mis5001 4-0031: supply avdd not found, using dummy regulator
[ 4.277686] mis5001 4-0031: supply dovdd not found, using dummy regulator
[ 4.277744] mis5001 4-0031: supply dvdd not found, using dummy regulator
[ 4.294595] mis5001 4-0031: Unexpected sensor id(000000), ret(-5)
[ 4.341745] rkcifhw ffa10000.rkcif: no iommu attached, using non-iommu buffers
[ 4.341766] rkcifhw ffa10000.rkcif: No reserved memory region assign to CIF
[ 4.342135] rkcif rkcif-mipi-lvds: rkcif driver version: v00.02.00
[ 4.342282] rkcif rkcif-mipi-lvds: attach to cif hw node
[ 4.342295] rkcif rkcif-mipi-lvds: failed to get dphy hw node
[ 4.342305] rkcif rkcif-mipi-lvds: rkcif wait line 0
[ 4.342315] rkcif rkcif-mipi-lvds: rkcif fastboot reserve bufs num 3
[ 4.342328] : terminal subdev does not exist
[ 4.342338] : terminal subdev does not exist
[ 4.342345] : terminal subdev does not exist
[ 4.342353] : terminal subdev does not exist
[ 4.342363] : get_remote_sensor: video pad[0] is null
[ 4.342372] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 4.342382] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 4.342391] : get_remote_sensor: video pad[0] is null
[ 4.342397] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 4.342406] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 4.342413] : get_remote_sensor: video pad[0] is null
OK
[ 4.342419] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 4.342428] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
Starting ntpd: [ 4.342435] : get_remote_sensor: video pad[0] is null
[ 4.342441] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 4.342449] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 4.363257] rkcif rkcif-mipi-lvds: No memory-region-thunderboot specified
[ 4.364413] rockchip-mipi-csi2-hw ffa20000.mipi-csi2-hw: enter mipi csi2 hw probe!
0
[ 4.364581] rockchip-mipi-csi2-hw ffa20000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[ 4.364714] rockchip-mipi-csi2-hw ffa30000.mipi-csi2-hw: enter mipi csi2 hw probe!
[ 4.364829] rockchip-mipi-csi2-hw ffa30000.mipi-csi2-hw: probe success, v4l2_dev:mipi-csi2-hw!
[ 4.365284] rockchip-mipi-csi2 mipi0-csi2: attach to csi2 hw node
[ 4.365356] rkcif rkcif-mipi-lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 4.365372] rockchip-mipi-csi2: Async registered subdev
[ 4.365379] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds!
[ 4.403679] rkisp_hw ffa00000.rkisp: is_thunderboot: 0
[ 4.403706] rkisp_hw ffa00000.rkisp: Missing rockchip,grf property
[ 4.403752] rkisp_hw ffa00000.rkisp: max input:0x0@0fps
[ 4.403914] rkisp_hw ffa00000.rkisp: get sram size:253952
[ 4.403927] rkisp_hw ffa00000.rkisp: no iommu attached, using non-iommu buffers
[ 4.403937] rkisp_hw ffa00000.rkisp: No reserved memory region. default cma area!
[ 4.404301] rkisp rkisp-vir0: rkisp driver version: v02.05.00
[ 4.404425] rkisp rkisp-vir0: No memory-region-thunderboot specified
[ 4.412253] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
0
[ 4.434311] rockchip-csi2-dphy-hw ff3e8000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[ 4.453206] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
OK
Starting sshd: 0
0
[ 4.880299] rkcif rkcif-mipi-lvds: clear unready subdev num: 2
[ 4.881257] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 4.881281] rkcif-mipi-lvds: Async subdev notifier completed
[ 4.881304] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 4.881313] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 4.881572] rkisp rkisp-vir0: clear unready subdev num: 1
[ 4.881788] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 4.881799] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 4.882300] rkisp-vir0: Async subdev notifier completed
[ 4.901857] rga: rga2, irq = 38, match scheduler
[ 4.905273] rga: rga2 hardware loaded successfully, hw_version:3.3.87975.
[ 4.905299] rga: rga2 probe successfully
[ 4.905588] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ 4.906565] rga: Module initialized. v1.3.1
[ 4.929325] mpp_vcodec: loading out-of-tree module taints kernel.
OK
[ 4.947774] mpp_vcodec: init new
[ 4.947910] mpp_service mpp-srv: 424abb9b author: Yandong Lin 2024-04-29 [mpp_enc]: fix wrap enc sw timeout when resolution switch
Starting telnetd: [ 4.947925] mpp_service mpp-srv: probe start
Input (null) Format:SRGGB8_1X8 Size:800x600@4fps Offset(0,0)
[ 4.952681] mpp_rkvenc_540c ffa50000.rkvenc: probing start
OK
[ 4.952925] mpp_rkvenc_540c ffa50000.rkvenc: probing finish
[ 4.953359] mpp_vepu_pp ffa60000.rkvenc-pp: probe device
[ 4.953457] mpp_vepu_pp ffa60000.rkvenc-pp: shared_rst_a_pp is not found!
[ 4.953468] vepu_pp_init:526: No aclk reset resource define
[ 4.953479] mpp_vepu_pp ffa60000.rkvenc-pp: shared_rst_h_pp is not found!
[ 4.953487] vepu_pp_init:529: No hclk reset resource define
[ 4.959294] mpp_vepu_pp ffa60000.rkvenc-pp: probing finish
[ 4.959566] mpp_service mpp-srv: probe success
[ 4.984137] RKNPU ff660000.npu: RKNPU: rknpu iommu device-tree entry not found!, using non-iommu mode
[ 4.985647] RKNPU ff660000.npu: RKNPU: Initialized RKNPU driver: v0.9.2 for 20230825
[ 4.985775] RKNPU ff660000.npu: dev_pm_opp_set_regulators: no regulator (rknpu) found: -19
/etc/init.d/S50usbdevice: line 144: can't open : no such file
[ 5.052081] rockit_load start
Debug: configfs_init
[ 5.076633] rockit_load end
[ 5.092549] rve: rve_irq, irq = 55, match scheduler
[ 5.095376] rve: Driver loaded successfully rve[2] ver:[2021]58.1a
[ 5.095400] rve: probe successfully
[ 5.096688] rve: Module initialized. v1.0.6
/
[ 5.141107] udevd[308]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video0': No such file or directory
[ 5.143829] udevd[309]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video1': No such file or directory
[ 5.148513] udevd[312]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video2': No such file or directory
ln: /oem/usr/www/userdata: No such file or directory
[ 5.149584] udevd[313]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video3': No such file or directory
[ 5.180513] udevd[321]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video4': No such file or directory
[ 5.181586] udevd[322]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video5': No such file or directory
[ 5.184150] udevd[323]: failed to execute '/lib/udev/v4l_id' 'v4l_id /dev/video6': No such file or directory
ln: /oem/usr/www/usb0: No such file or directory
ln: /oem/usr/www/sdcard: No such file or directory
[ 5.333948] file system registered
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/mtp.gs0': No such file or directory
[ 5.499118] using random self ethernet address
[ 5.499152] using random host ethernet address
mkdir: can't create directory '/sys/kernel/config/usb_gadget/rockchip/functions/acm.gs6': No such file or directory
[ 5.595723] Mass Storage Function, version: 2009/09/11
[ 5.595759] LUN: removable file: (no medium)
Error: not found rkipc.ini !!!
/oem/usr/bin/RkLunch.sh: exit: line 119: Illegal number: -1
[ 5.641215] rk_gmac-dwmac ffa80000.ethernet eth0: PHY [stmmac-0:02] driver [RK630 PHY] (irq=POLL)
[ 5.642098] dwmac4: Master AXI performs any burst length
[ 5.642139] rk_gmac-dwmac ffa80000.ethernet eth0: No Safety Features support found
[ 5.642161] rk_gmac-dwmac ffa80000.ethernet eth0: PTP not supported by HW
[ 5.642463] rk_gmac-dwmac ffa80000.ethernet eth0: configuring for phy/rmii link mode
[ 5.761558] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.800489] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.800727] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 5.800745] cfg80211: failed to load regulatory.db
[ 5.830303] read descriptors
[ 5.830377] read strings
insmod: can't insert 'libaes.ko': No such file or directory
[ 5.856987] aicbsp_init
[ 5.857014] RELEASE_DATE:2025_0410_b99ca8b6
[ 5.857025] aicbsp_resv_mem_init
[ 6.094154] aicbsp: aicbsp_set_subsys, subsys: AIC_WIFI, state to: 1
[ 6.094183] aicbsp: aicbsp_set_subsys, power state change to 1 dure to AIC_WIFI
[ 6.094190] aicbsp: aicbsp_platform_power_on
[ 6.117047] aicbsp: aicbsp_sdio_probe:1 vid:0xC8A1 did:0xC08D
[ 6.117203] aicbsp: aicbsp_sdio_probe:2 vid:0xC8A1 did:0xC18D
[ 6.117218] aicbsp: aicbsp_sdio_probe after replace:1
[ 6.117228] AICWFDBG(LOGINFO) aicwf_sdio_chipmatch USE AIC8800DC
[ 6.117235] the device is PRODUCT_ID_AIC8800DC
[ 6.117243] aicbsp: aicbsp_get_feature, set FEATURE_SDIO_CLOCK 50 MHz
[ 6.117249] aicbsp: aicwf_sdio_reg_init
[ 6.117448] aicbsp: Set SDIO Clock 50 MHz
[ 6.120645] AICWFDBG(LOGINFO) btenable = 1
[ 6.120666] AICWFDBG(LOGINFO) aicbsp: aicbsp_driver_fw_init, chip rev: 7
[ 6.120680] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fw_patch_table_8800dc_u02.bin
[ 6.121894] file md5:34860725322202bfc2d80843297562ee
[ 6.121992] AICWFDBG(LOGDEBUG) aicbt_patch_info_unpack head_t->len:6 base_len:4
[ 6.122002] AICWFDBG(LOGDEBUG) aicbt_patch_info_unpack memcpy_len:5
[ 6.122010] AICWFDBG(LOGDEBUG) aicbt_patch_info_unpack adid_addrinf:194b44 addr_adid:1017d8
[ 6.122018] AICWFDBG(LOGDEBUG) aicbt_patch_info_unpack id:0 addr:194000
[ 6.122025] rwnx_plat_bin_fw_upload_android
[ 6.122034] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fw_adid_8800dc_u02.bin
[ 6.122501] file md5:95d10e6288e4d3413c0e3508cb9d711a
[ 6.123142] rwnx_plat_bin_fw_upload_android
[ 6.123159] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fw_patch_8800dc_u02.bin
[ 6.124376] file md5:675951fc926375001f974d729f097164
[ 6.131025] AICWFDBG(LOGDEBUG) [0x40506004]: 0x04318000
[ 6.131241] AICWFDBG(LOGDEBUG) [0x40506004]: 0x04338000
[ 6.131447] AICWFDBG(LOGDEBUG) aicbt_ext_patch_data_load ext_patch_file_name:fw_patch_8800dc_u02_ext0.bin ext_patch_id:0 ext_patch_addr:194000
[ 6.131457] rwnx_plat_bin_fw_upload_android
[ 6.131467] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fw_patch_8800dc_u02_ext0.bin
[ 6.132044] file md5:d783d229be5a485fdb39cc018abaf55b
[ 6.145435] aicbt_patch_table_load bt btmode[1]:1
[ 6.145452] aicbt_patch_table_load bt uart_baud[1]:1500000
[ 6.145459] aicbt_patch_table_load bt uart_flowctrl[1]:1
[ 6.145465] aicbt_patch_table_load bt lpm_enable[1]:0
[ 6.145471] aicbt_patch_table_load bt tx_pwr[1]:28463
[ 6.150156] aicbsp: bt patch version: - Mar 17 2025 11:27:16 - git a6547a6
[ 6.150218] ############ aicwifi_init begin
[ 6.150521] AICWFDBG(LOGINFO) chip_id=7, chip_sub_id=1!!
[ 6.150677] AICWFDBG(LOGDEBUG) set_bbpll_config rd_mem_addr_cfm.memdata:c
[ 6.150687] AICWFDBG(LOGINFO) set_bbpll_config Crystal not provided by CPU
[ 6.150888] AICWFDBG(LOGDEBUG) [0x40500010]=6
[ 6.154315] ############ system_config_8800dc done
[ 6.154327] AICWFDBG(LOGTRACE) >>> rwnx_plat_patch_load()
[ 6.154333] AICWFDBG(LOGINFO) testmode=0
[ 6.154339] AICWFDBG(LOGINFO) rwnx_plat_patch_loading
[ 6.154346] u02 is loaing ###############
[ 6.154351] rwnx_plat_bin_fw_upload_android
[ 6.154360] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fmacfw_patch_8800dc_u02.bin
[ 6.156957] file md5:ec8ee791723f4bf9825a6c153a7f0a8f
[ 6.163269] AICWFDBG(LOGINFO) dpd calib & write
[ 6.163287] aicwf_dpd_calib_8800dc
[ 6.163454] AICWFDBG(LOGERROR) misc_ram_addr=120ebc
[ 6.164008] AICWFDBG(LOGTRACE) bit_mask:2663e94c,e5ee8694,319ffcbb,90cd4ee6
[ 6.164020] rwnx_plat_bin_fw_upload_android
[ 6.164031] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fmacfw_calib_8800dc_u02.bin
[ 6.166219] file md5:061790c6181e5974a4c44c515e6d0b69
[ 6.174428] AICWFDBG(LOGINFO) Start app: 00130009, 4
[ 6.396077] ############ rwnx_plat_patch_load done
[ 6.396660] AICWFDBG(LOGINFO) wifisetting_cfg_addr=11019c, ldpc_cfg_addr=120980, agc_cfg_addr=120180, txgain_cfg_addr=120000
[ 6.398374] ### Upload fmacfw_patch_tbl_8800dc_u02.bin
[ 6.398391] rwnx_load_firmware :firmware path = /oem/usr/ko/aic8800dc_fw/fmacfw_patch_tbl_8800dc_u02.bin
[ 6.411560] file md5:c0538d7493963b1f37938e6e87f9e304
[ 6.411578] tbl size = 1008
[ 6.411588] AICWFDBG(LOGINFO) FMACFW_PATCH_TBL_8800DC_U02_DESCRIBE_BASE = 187c00
[ 6.411856] di Mar 14 2025 12:29:38 - g09cea8d
[ 6.411865] patch_tbl: 110888 181219
[ 6.412038] patch_tbl: 1108ec 184d59
[ 6.412191] patch_tbl: 110874 181279
[ 6.412343] patch_tbl: 110658 181b09
[ 6.412492] patch_tbl: 1107dc 1874dd
[ 6.412639] patch_tbl: 11055c 184135
[ 6.412783] patch_tbl: 110758 187485
[ 6.412929] patch_tbl: 110620 187631
[ 6.413077] patch_tbl: 1107e0 181b99
[ 6.413226] patch_tbl: 110838 181dd5
[ 6.413419] patch_tbl: 1104f4 182045
[ 6.413570] patch_tbl: 110490 182f6d
[ 6.413721] patch_tbl: 110420 1822b1
[ 6.413866] patch_tbl: 11048c 1823cd
[ 6.414016] patch_tbl: 110688 182471
[ 6.414163] patch_tbl: 110738 182ead
[ 6.414309] patch_tbl: 110528 1877a1
[ 6.414459] patch_tbl: 110554 182fc1
[ 6.414604] patch_tbl: 110798 183615
[ 6.414750] patch_tbl: 1106dc 183061
[ 6.416614] patch_tbl: 110584 1830fd
[ 6.416814] patch_tbl: 110588 1832d5
[ 6.416979] patch_tbl: 110634 1854e1
[ 6.417130] patch_tbl: 110638 1856b9
[ 6.417283] patch_tbl: 110640 1858c1
[ 6.417432] patch_tbl: 11086c 18597d
[ 6.417578] patch_tbl: 1105fc 1859d9
[ 6.417727] patch_tbl: 1105f0 18655d
[ 6.417873] patch_tbl: 110860 185641
[ 6.418021] patch_tbl: 11081c 185131
[ 6.418164] patch_tbl: 1105a4 185dc1
[ 6.418309] patch_tbl: 1105c8 185e91
[ 6.418456] patch_tbl: 110810 1851e9
[ 6.418600] patch_tbl: 1108c4 183869
[ 6.418746] patch_tbl: 1108c8 183705
[ 6.418962] patch_tbl: 110628 1839e1
[ 6.419112] patch_tbl: 110750 18664d
[ 6.419262] patch_tbl: 1106d8 186691
[ 6.419408] patch_tbl: 11085c 183e45
[ 6.419556] patch_tbl: 110518 186945
[ 6.419709] patch_tbl: 1105e0 181f7d
[ 6.419857] patch_tbl: 1107d8 18368d
[ 6.420005] patch_tbl: 1103d0 1869a5
[ 6.420151] patch_tbl: 1106c8 186f81
[ 6.420299] patch_tbl: 11056c 186f4d
[ 6.420445] patch_tbl: 1106b4 185309
[ 6.420589] patch_tbl: 110510 187071
[ 6.420734] patch_tbl: 110550 18710d
[ 6.420883] patch_tbl: 1104ec 1842a1
[ 6.421029] patch_tbl: 1106d4 187389
[ 6.421176] patch_tbl: 11064c 186241
[ 6.421322] patch_tbl: 110494 184675
[ 6.421469] patch_tbl: 110734 184689
[ 6.421616] patch_tbl: 11047c 1873d1
[ 6.421761] patch_tbl: 110740 18757d
[ 6.421909] patch_tbl: 110880 1875e9
[ 6.422055] patch_tbl: 110054 181b09
[ 6.422201] patch_tbl: 11005c 181b09
[ 6.422352] patch_tbl: 110048 182f6d
[ 6.422500] patch_tbl: 110088 185929
[ 6.422648] patch_tbl: 1100c4 185309
[ 6.422798] patch_tbl: 110ef0 185b55
[ 6.422945] patch_tbl: 110ec0 183c15
[ 6.423092] patch_tbl: 110da0 183c35
[ 6.423241] patch_tbl: 110dc0 183ded
[ 6.423390] patch_tbl: 110e28 183d81
[ 6.423535] patch_tbl: 1100e0 183d2d
[ 6.423683] patch_tbl: 110d88 183e29
[ 6.423829] patch_tbl: 110d90 186721
[ 6.423976] patch_tbl: 110e18 183b95
[ 6.424123] patch_tbl: 110bb4 18740d
[ 6.424322] patch_tbl: 110960 1835f9
[ 6.424474] patch_tbl: 1109c0 18205d
[ 6.424625] patch_tbl: 110f08 182291
[ 6.424775] patch_tbl: 110b1c 183619
[ 6.428442] patch_tbl: 110b24 183619
[ 6.428626] patch_tbl: 110b5c 182585
[ 6.428789] patch_tbl: 110b64 182585
[ 6.428943] patch_tbl: 110b6c 182585
[ 6.429095] patch_tbl: 110b74 182585
[ 6.429248] patch_tbl: 110b7c 182585
[ 6.429398] patch_tbl: 110b8c 182585
[ 6.429546] patch_tbl: 110b44 1858c1
[ 6.429696] patch_tbl: 110ac0 184311
[ 6.429887] patch_tbl: 110aa0 183575
[ 6.430040] patch_tbl: 110aa8 1835dd
[ 6.430188] patch_tbl: 110a60 186ea1
[ 6.430338] patch_tbl: 110e20 186f15
[ 6.430487] patch_tbl: 110f3c 187259
[ 6.430634] patch_tbl: 110d28 1872ad
[ 6.430781] patch_tbl: 111418 1871a1
sh: write error: No such device
[ 6.430929] patch_tbl: 40030084 187c80
[ 6.431076] patch_tbl: 40030000 46e68
[ 6.431223] patch_tbl: 40030004 2778c
[ 6.431373] patch_tbl: 40030008 40908
[ 6.431519] patch_tbl: 4003000c 13824
[ 6.431665] patch_tbl: 40030010 13864
[ 6.431812] patch_tbl: 40030014 13868
[ 6.431958] patch_tbl: 40030018 138e4
[ 6.432106] patch_tbl: 4003001c 138e8
[ 6.432254] patch_tbl: 187c80 d0332b00
[ 6.432400] patch_tbl: 187c84 47706008
[ 6.432544] patch_tbl: 187c88 47702001
[ 6.432692] patch_tbl: 187c8c bf00bf00
[ 6.432835] patch_tbl: 187c90 bf004832
[ 6.432981] patch_tbl: 187c94 f3efbf00
[ 6.433127] patch_tbl: 187c98 bf004812
[ 6.433275] patch_tbl: 187c9c 4620bf00
[ 6.433424] patch_tbl: 40030080 fb
[ 6.433566] patch_tbl: 4010001c 0
[ 6.433728] ############ aicwf_patch_config_8800dc done
[ 6.433739] AICWFDBG(LOGINFO) Read FW mem: 00120000
[ 6.433888] AICWFDBG(LOGINFO) cfm: [00120000] = 00ffd780
[ 6.433897] AICWFDBG(LOGINFO) Start app: 00120000, 5
[ 6.438231] aicbsp: aicbsp_get_feature, set FEATURE_SDIO_CLOCK 50 MHz
[ 6.438249] aicsdio: aicwf_sdio_reg_init
[ 6.448876] aicbsp: aicbsp_resv_mem_alloc_skb, alloc resv_mem_txdata succuss, id: 0, size: 98304
[ 6.449159] aicbsp: aicbsp_get_feature, set FEATURE_SDIO_CLOCK 50 MHz
[ 6.449337] tcp_ack_init
[ 6.449356] AICWFDBG(LOGINFO) aicwf_prealloc_txq_alloc size is diff will to be kzalloc
[ 6.449381] AICWFDBG(LOGINFO) aicwf_prealloc_txq_alloc txq kzalloc successful
[ 6.474855] aicbsp: sdio_err:<aicwf_sdio_bus_pwrctl,1449>: bus down
[ 6.725457] ieee80211 phy0: HT supp 1, VHT supp 1, HE supp 1
[ 6.727552] ieee80211 phy0:
[ 6.727552] *******************************************************
[ 6.727552] ** CAUTION: USING PERMISSIVE CUSTOM REGULATORY RULES **
[ 6.727552] *******************************************************
[ 6.736811] get_txpwr_max:txpwr_max:20
ifconfig: SIOCSIFADDR: No such device
ifconfig: SIOCGIFFLAGS: No such device
Starting SMB services: [ 8.793191] aic_bluetooth_mod_init
[ 8.793565] -->rfkill_bluetooth_init
[ 8.793688] <--rfkill_bluetooth_init
[ 10.219418] get_txpwr_max:txpwr_max:20
[ 10.219566] get_txpwr_max:txpwr_max:20
[ 10.220452] get_txpwr_max:txpwr_max:20
[ 10.220554] get_txpwr_max:txpwr_max:20
[ 10.221824] get_txpwr_max:txpwr_max:20
OK
Starting NMB services: OK
[ 11.722139] of_dma_request_slave_channel: dma-names property of node '/serial@ff4b0000' missing or empty
Device setup complete
[ 11.722173] dw-apb-uart ff4b0000.serial: failed to request DMA, use interrupt mode
/usr/bin/luckfox-config: line 262: warning: command substitution: ignored null byte in input
Only Luckfox Pico Ultra /Luckfox Pico Ultra W support RGB
Complete configuration loading
/root/main.py and /root/boot.py not exist ,pass...
OK
RTC does not require time calibration
Welcome to luckfox pico
luckfox login: