Luckfox Pico Plus 更换新的Flash后，如何更改FLASH ID,从而烧录固件

  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    SPI NAND FLASH Image burning
  • Crocodile Engineer
    Engineer
    Posts: 909
    Joined: 2024-01-23 7:21

    wenjie wrote: ↑2024-06-06 9:53 更换Flash后，烧录固件时提示Write LBA faild!
    您好，出现Write LBA faild!的情况有很多种（比如线材问题或者电脑USB口问题），不一定是flash出现问题，如果有条件的话可以使用串口模块观察一下烧录模式下串口的输出（UART2_M1 靠近TypeC 口的串口），观察是否有其它日志的打印。Flash 目前我们仅测试过芯片上的这一款，如果您使用的是其它型号的flash芯片可能因为其它因素导致下载失败，我们也无法提供帮助。
  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    Crocodile wrote: ↑2024-06-06 10:17
    wenjie wrote: ↑2024-06-06 9:53 更换Flash后，烧录固件时提示Write LBA faild!
    您好，出现Write LBA faild!的情况有很多种（比如线材问题或者电脑USB口问题），不一定是flash出现问题，如果有条件的话可以使用串口模块观察一下烧录模式下串口的输出（UART2_M1 靠近TypeC 口的串口），观察是否有其它日志的打印。Flash 目前我们仅测试过芯片上的这一款，如果您使用的是其它型号的flash芯片可能因为其它因素导致下载失败，我们也无法提供帮助。
    The cable and the computer USB port are good
    Last edited by wenjie on 2024-06-07 2:38, edited 1 time in total.
  • Crocodile Engineer
    Engineer
    Posts: 909
    Joined: 2024-01-23 7:21

    wenjie wrote: ↑2024-06-07 1:56
    Crocodile wrote: ↑2024-06-06 10:17
    wenjie wrote: ↑2024-06-06 9:53 更换Flash后，烧录固件时提示Write LBA faild!
    您好，出现Write LBA faild!的情况有很多种（比如线材问题或者电脑USB口问题），不一定是flash出现问题，如果有条件的话可以使用串口模块观察一下烧录模式下串口的输出（UART2_M1 靠近TypeC 口的串口），观察是否有其它日志的打印。Flash 目前我们仅测试过芯片上的这一款，如果您使用的是其它型号的flash芯片可能因为其它因素导致下载失败，我们也无法提供帮助。
    The cable and the computer USB port are good

    Could you provide the serial port print information?
  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    Code: Select all

    RKUARTDDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
fc27
rgef0
rgef1
DDRConf1
DDR2, BW=16 Col=10 Bk=4 CS0 Row=13 CS=1 Die BW=16 Size=64MB
528MHz
DDR bin out

Boot1 Release Time: Aug 12 2022 17:14:00, version: 1.06 NO FTL
rom_version: 0x30303256
Boot from dev = 129
hamming_distance:1103 1106 2
chip_id:5256110300,0
ChipType = 27
0xff3e0040: 0x49
sfc nor id: ff ff ff
sfc_nand id: ff ff ff
Set sdmmc2 Clk: 200, 1
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
SdmmcInit=2 1
UsbBoot ...33728
0xff3e0040: 0x49
powerOn 38997
  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    Crocodile wrote: ↑2024-06-07 3:49
    wenjie wrote: ↑2024-06-07 1:56
    Crocodile wrote: ↑2024-06-06 10:17

    您好，出现Write LBA faild!的情况有很多种（比如线材问题或者电脑USB口问题），不一定是flash出现问题，如果有条件的话可以使用串口模块观察一下烧录模式下串口的输出（UART2_M1 靠近TypeC 口的串口），观察是否有其它日志的打印。Flash 目前我们仅测试过芯片上的这一款，如果您使用的是其它型号的flash芯片可能因为其它因素导致下载失败，我们也无法提供帮助。
    The cable and the computer USB port are good

    Could you provide the serial port print information?

    Code: Select all

    RKUARTDDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
fc27
rgef0
rgef1
DDRConf1
DDR2, BW=16 Col=10 Bk=4 CS0 Row=13 CS=1 Die BW=16 Size=64MB
528MHz
DDR bin out

Boot1 Release Time: Aug 12 2022 17:14:00, version: 1.06 NO FTL
rom_version: 0x30303256
Boot from dev = 129
hamming_distance:1103 1106 2
chip_id:5256110300,0
ChipType = 27
0xff3e0040: 0x49
sfc nor id: ff ff ff
sfc_nand id: ff ff ff
Set sdmmc2 Clk: 200, 1
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
SdmmcInit=2 1
UsbBoot ...33728
0xff3e0040: 0x49
powerOn 38997
  • Crocodile Engineer
    Engineer
    Posts: 909
    Joined: 2024-01-23 7:21

    wenjie wrote: ↑2024-06-07 8:39
    Crocodile wrote: ↑2024-06-07 3:49
    wenjie wrote: ↑2024-06-07 1:56
    The cable and the computer USB port are good

    Could you provide the serial port print information?

    Code: Select all

    RKUARTDDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
fc27
rgef0
rgef1
DDRConf1
DDR2, BW=16 Col=10 Bk=4 CS0 Row=13 CS=1 Die BW=16 Size=64MB
528MHz
DDR bin out

Boot1 Release Time: Aug 12 2022 17:14:00, version: 1.06 NO FTL
rom_version: 0x30303256
Boot from dev = 129
hamming_distance:1103 1106 2
chip_id:5256110300,0
ChipType = 27
0xff3e0040: 0x49
sfc nor id: ff ff ff
sfc_nand id: ff ff ff
Set sdmmc2 Clk: 200, 1
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
SdmmcInit=2 1
UsbBoot ...33728
0xff3e0040: 0x49
powerOn 38997
    Can you access the system via SD card? You can test with the system provided in the cloud drive.
    In previous tests to verify the normal operation of the product, I encountered a situation similar to yours, and ultimately found that the main control chip was short-circuited. So, please observe whether the chip heats up significantly when powered on, or use a regulated DC power supply to test if the chip is receiving power properly.
  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    Crocodile wrote: ↑2024-06-07 9:02
    wenjie wrote: ↑2024-06-07 8:39
    Crocodile wrote: ↑2024-06-07 3:49


    Could you provide the serial port print information?

    Code: Select all

    RKUARTDDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
fc27
rgef0
rgef1
DDRConf1
DDR2, BW=16 Col=10 Bk=4 CS0 Row=13 CS=1 Die BW=16 Size=64MB
528MHz
DDR bin out

Boot1 Release Time: Aug 12 2022 17:14:00, version: 1.06 NO FTL
rom_version: 0x30303256
Boot from dev = 129
hamming_distance:1103 1106 2
chip_id:5256110300,0
ChipType = 27
0xff3e0040: 0x49
sfc nor id: ff ff ff
sfc_nand id: ff ff ff
Set sdmmc2 Clk: 200, 1
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
SdmmcInit=2 1
UsbBoot ...33728
0xff3e0040: 0x49
powerOn 38997
    Can you access the system via SD card? You can test with the system provided in the cloud drive.
    In previous tests to verify the normal operation of the product, I encountered a situation similar to yours, and ultimately found that the main control chip was short-circuited. So, please observe whether the chip heats up significantly when powered on, or use a regulated DC power supply to test if the chip is receiving power properly.
    Luckfork Pikoppleluth was unable to find the Staka version of the firmware.
    Image
  • wenjie
    Posts: 69
    Joined: 2024-06-06 9:43

    Crocodile wrote: ↑2024-06-07 9:02
    wenjie wrote: ↑2024-06-07 8:39
    Crocodile wrote: ↑2024-06-07 3:49


    Could you provide the serial port print information?

    Code: Select all

    RKUARTDDR V1.10 ec2fae0c96 wesley.yao 22/11/15-10:58:09
S5P1
fc27
rgef0
rgef1
DDRConf1
DDR2, BW=16 Col=10 Bk=4 CS0 Row=13 CS=1 Die BW=16 Size=64MB
528MHz
DDR bin out

Boot1 Release Time: Aug 12 2022 17:14:00, version: 1.06 NO FTL
rom_version: 0x30303256
Boot from dev = 129
hamming_distance:1103 1106 2
chip_id:5256110300,0
ChipType = 27
0xff3e0040: 0x49
sfc nor id: ff ff ff
sfc_nand id: ff ff ff
Set sdmmc2 Clk: 200, 1
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
emmc reinit
Set sdmmc2 Clk: 200, 1
 SDC_BusRequest:  CMD=1  SDC_RESP_TIMEOUT 1736
 mmc2:cmd1,20
SdmmcInit=2 1
UsbBoot ...33728
0xff3e0040: 0x49
powerOn 38997
    Can you access the system via SD card? You can test with the system provided in the cloud drive.
    In previous tests to verify the normal operation of the product, I encountered a situation similar to yours, and ultimately found that the main control chip was short-circuited. So, please observe whether the chip heats up significantly when powered on, or use a regulated DC power supply to test if the chip is receiving power properly.
    Luckfork Pikoppleluth was unable to find the SD card version of the firmware.
    There is no obvious heating when the chip is powered on, and the chip is powered on normally.
    Image
    Last edited by wenjie on 2024-06-07 10:10, edited 1 time in total.
    • Post Reply

    Return to “LuckFox Pico”